More v2 images and case info

doc/buildguide_v2.md

@@ -9,8 +9,7 @@ to try their hand at building their own keyboard.
 
 I assume you read the [ordering guide](orderingguide.md) and have all the mandatory parts and tools.
 
-![V2 by soul_wish](images/buildguidev2/v2.png)
-V2 build by soul_wish: https://www.reddit.com/r/ErgoMechKeyboards/comments/1c5njbj/my_first_build_cheapino_v2/
+This guy also documented his build very good: https://imgur.com/a/building-cheapino-as-complete-beginner-G8dDaJi
 
 ## Steps
 

doc/plates_and_cases.md

@@ -5,6 +5,8 @@ Plates and cases
 It has no support or screw inserts, so not ideal for hotswap
 builds, but does the job.
 
+![Case](../images/v1/v1_with_plate.jpg)
+
 ## V2
 
 This is the basically the same plate with a few supports
@@ -18,6 +20,7 @@ https://www.thingiverse.com/thing:6661648
 
 Lots of pictures here: https://imgur.com/a/cheapino-2-case-R4ialST
 
+![Case](../images/case.jpg)
 
 TheMadClover made 2 really nice looking case options, one tented,
 and one flat, check them out here:
@@ -30,5 +33,11 @@ This is a VERY nice case with built-in support for tenting
 and a travel solution:
 https://www.printables.com/model/835134-cheapino-split-keyboard-case
 
+
+![Case](../images/v1/case2.jpg)
+
 This is a case for v1 with a simple tenting solution:
 https://www.printables.com/model/541536-cheapino-case-with-basic-tenting
+
+
+![Case](../images/v1/case.jpeg)

doc/v1.md

@@ -0,0 +1,56 @@
+Cheapino V1 (Obsolete)
+========
+
+The V1 and V2 are not that different, they have the same key layout, but V2 has a lot of minor improvements, so I suggest building that!
+
+Here are some V1 images:
+
+![Cheapino by finex](../images/v1/otherbuild8.jpeg)
+
+https://www.reddit.com/r/ErgoMechKeyboards/comments/12xg4u7/built_the_cheapino/
+![Cheapino by TentacleSenpai69](../images/v1/otherbuild.jpeg)
+
+https://www.reddit.com/r/ErgoMechKeyboards/comments/13c274r/cheapino_build/
+![Cheapino by Palbi](../images/v1/otherbuild2.jpeg)
+
+https://discuss.tchncs.de/post/410101
+![Cheapino by PixelPrimer](../images/v1/otherbuild3.jpeg)
+
+https://discuss.tchncs.de/post/852362
+![Cheapino by Chraccoon](../images/v1/otherbuild4.jpeg)
+
+https://lemmy.world/post/2080485
+![Cheapino by Hansamann](../images/v1/otherbuild5.jpeg)
+
+https://lemmy.world/post/2832967
+![Cheapino by createkarma](../images/v1/otherbuild6.jpeg)
+
+![Cheapino by ??](../images/v1/otherbuild7.jpeg)
+
+https://www.reddit.com/r/ErgoMechKeyboards/comments/18i5jpu/first_build_cheapino/
+![Cheapino by lydomixian](../images/v1/otherbuild9.jpeg)
+
+https://www.reddit.com/r/ErgoMechKeyboards/comments/18zb3l1/first_build_finally_cheapino/
+![Cheapino by u/Tech-Buffoon](../images/v1/otherbuild10.jpeg)
+
+
+https://lemmy.world/post/2480447
+![Case by Chraccoon](../images/v1/case.jpeg)
+Printable file  for the case here: https://www.printables.com/model/541536-cheapino-case-with-basic-tenting
+
+Probably the cheapest tenting solution: https://www.reddit.com/r/ErgoMechKeyboards/comments/16s3yb2/cheapino/
+![Cheapino by @JordanNiphan](../images/v1/otherbuild11.jpeg)
+
+@keyboard-magpie made a plate which will help position the switches: [plate.stl](../plates/v1_plate.stl)
+
+@ggppjj made some useful modifications to miryoku and enabled LED for that as well here: https://github.com/ggppjj/qmk_firmware/releases
+
+Drawbacks:
+
+* V1 only: Without a plate, its pretty difficult to solder swithes straight. I made a small helper "fork" to hold each column in place when soldering. Check the build guide for a link to a really good 3D printed fork.
+* RJ45 cables are a bit rigid, so they do not lay down on the table nicely like audio cables.
+* There is no official qmk support, you need to compile from my branch manually... Keymap can be edited in qmk configurator though.
+
+
+![Cheapino PCB](../images/v1/cheapino_pcb.jpg "Cheapino PCB")
+