RGB Matrix Overhaul (#5372)

* RGB Matrix overhaul
Breakout of animations to separate files
Integration of optimized int based math lib
Overhaul of rgb_matrix.c and animations for performance

* Updating effect function api for future extensions

* Combined the keypresses || keyreleases define checks into a single define so I stop forgetting it where necessary

* Moving define RGB_MATRIX_KEYREACTIVE_ENABLED earlier in the include chain

Dockerfile

@@ -26,4 +26,4 @@ VOLUME /qmk_firmware
 WORKDIR /qmk_firmware
 COPY . .
 
-CMD make $KEYBOARD:$KEYMAP
+CMD make clean ; make git-submodule ; make $KEYBOARD:$KEYMAP

docs/config_options.md

@@ -171,11 +171,15 @@ If you define these options you will enable the associated feature, which may in
 ## RGB Light Configuration
 
 * `#define RGB_DI_PIN D7`
-  * pin the DI on the ws2812 is hooked-up to
+  * pin the DI on the WS2812 is hooked-up to
 * `#define RGBLIGHT_ANIMATIONS`
   * run RGB animations
-* `#define RGBLED_NUM 15`
+* `#define RGBLED_NUM 12`
   * number of LEDs
+* `#define RGBLED_SPLIT { 6, 6 }`
+  * number of LEDs connected that are directly wired to `RGB_DI_PIN` on each half of a split keyboard
+  * First value indicates number of LEDs for left half, second value is for the right half
+  * Needed if both halves of the board have RGB LEDs wired directly to the RGB output pin on the controllers instead of passing the output of the left half to the input of the right half
 * `#define RGBLIGHT_HUE_STEP 12`
   * units to step when in/decreasing hue
 * `#define RGBLIGHT_SAT_STEP 25`
@@ -236,6 +240,9 @@ There are a few different ways to set handedness for split keyboards (listed in
 * `#define MATRIX_COL_PINS_RIGHT { <col pins> }`
   * If you want to specify a different pinout for the right half than the left half, you can define `MATRIX_ROW_PINS_RIGHT`/`MATRIX_COL_PINS_RIGHT`. Currently, the size of `MATRIX_ROW_PINS` must be the same as `MATRIX_ROW_PINS_RIGHT` and likewise for the definition of columns.
 
+* `#define RGBLED_SPLIT { 6, 6 }`
+  * See [RGB Light Configuration](#rgb-light-configuration)
+
 * `#define SELECT_SOFT_SERIAL_SPEED <speed>` (default speed is 1)
   * Sets the protocol speed when using serial communication
   * Speeds:

docs/custom_quantum_functions.md

@@ -235,7 +235,7 @@ This example, running after everything else has initialized, sets up the rgb und
 void keyboard_post_init_user(void) {
   // Call the post init code.
   rgblight_enable_noeeprom(); // enables Rgb, without saving settings
-  rgblight_sethsv_noeeprom(180, 255, 255): // sets the color to teal/cyan without saving
+  rgblight_sethsv_noeeprom(180, 255, 255); // sets the color to teal/cyan without saving
   rgblight_mode_noeeprom(RGBLIGHT_MODE_BREATHING + 3); // sets mode to Fast breathing without saving
 }
 ```
@@ -342,7 +342,7 @@ This is an example of how to add settings, and read and write it. We're using th
 
 
 In your keymap.c file, add this to the top:
-```
+```c
 typedef union {
   uint32_t raw;
   struct {
@@ -358,7 +358,7 @@ This sets up a 32 bit structure that we can store settings with in memory, and w
 We're using `rgb_layer_change`, for the `layer_state_set_*` function, and use `keyboard_post_init_user` and `process_record_user` to configure everything. 
 
 Now, using the `keyboard_post_init_user` code above, you want to add `eeconfig_read_user()` to it, to populate the structure you've just created. And you can then immediately use this structure to control functionality in your keymap.  And It should look like: 
-```
+```c
 void keyboard_post_init_user(void) {
   // Call the keymap level matrix init.
 
@@ -375,7 +375,7 @@ void keyboard_post_init_user(void) {
 ```
 The above function will use the EEPROM config immediately after reading it, to set the default layer's RGB color. The "raw" value of it is converted in a usable structure based on the "union" that you created above. 
 
-```
+```c
 uint32_t layer_state_set_user(uint32_t state) {
     switch (biton32(state)) {
     case _RAISE:
@@ -397,8 +397,8 @@ uint32_t layer_state_set_user(uint32_t state) {
   return state;
 }
 ```
-This will cause the RGB underglow to be changed ONLY if the value was enabled.  Now to configure this value, create a new keycode for `process_record_user` called `RGB_LYR` and `EPRM`. Additionally, we want to make sure that if you use the normal RGB codes, that it turns off  Using the example above, make it look this:
-```
+This will cause the RGB underglow to be changed ONLY if the value was enabled.  Now to configure this value, create a new keycode for `process_record_user` called `RGB_LYR`. Additionally, we want to make sure that if you use the normal RGB codes, that it turns off  Using the example above, make it look this:
+```c
 
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
   switch (keycode) {
@@ -415,11 +415,6 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) {
             PLAY_NOTE_ARRAY(tone_qwerty);
         }
         return true; // Let QMK send the enter press/release events
-    case EPRM:
-        if (record->event.pressed) {
-            eeconfig_init(); // resets the EEPROM to default
-        }
-        return false;
     case RGB_LYR:  // This allows me to use underglow as layer indication, or as normal
         if (record->event.pressed) { 
             user_config.rgb_layer_change ^= 1; // Toggles the status
@@ -442,9 +437,9 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) {
   }
 }
 ```
-And lastly, you want to add the `eeconfig_init_user` function, so that when the EEPROM is reset, you can specify default values, and even custom actions. For example, if you want to set rgb layer indication by default, and save the default valued. 
+And lastly, you want to add the `eeconfig_init_user` function, so that when the EEPROM is reset, you can specify default values, and even custom actions. To force an EEPROM reset, use the `EEP_RST` keycode or [Bootmagic](feature_bootmagic.md) functionallity. For example, if you want to set rgb layer indication by default, and save the default valued. 
 
-```
+```c
 void eeconfig_init_user(void) {  // EEPROM is getting reset! 
   user_config.raw = 0;
   user_config.rgb_layer_change = true; // We want this enabled by default

docs/faq_build.md

@@ -36,6 +36,12 @@ SUBSYSTEMS=="usb", ATTRS{idVendor}=="03eb", ATTRS{idProduct}=="2ff0", MODE:="066
 # tmk keyboard products     https://github.com/tmk/tmk_keyboard
 SUBSYSTEMS=="usb", ATTRS{idVendor}=="feed", MODE:="0666"
 ```
+**/etc/udev/rules.d/54-input-club-keyboard.rules:**
+
+```
+# Input Club keyboard bootloader
+SUBSYSTEMS=="usb", ATTRS{idVendor}=="1c11", MODE:="0666"
+```
 
 ### Serial device is not detected in bootloader mode on Linux
 Make sure your kernel has appropriate support for your device. If your device uses USB ACM, such as

docs/feature_grave_esc.md

@@ -18,7 +18,7 @@ If Mary presses GESC on her keyboard, the OS will see an KC_ESC character. Now i
 
 ### Caveats
 
- * On macOS CMD/GUI + KC_GRV is actually mapped to a hot key so it will not output a backtick.
+On macOS, Command+<code>&#96;</code> is by default mapped to "Move focus to next window" so it will not output a backtick. Additionally, Terminal always recognises this shortcut to cycle between windows, even if the shortcut is changed in the Keyboard preferences.
 
 ## Configuration
 

docs/feature_mouse_keys.md

@@ -1,48 +1,48 @@
 # Mousekeys
 
 
-Mousekeys is a feature that allows you to emulate a mouse using your keyboard. You can move the pointer around, click up to 5 buttons, and even scroll in all 4 directions. QMK uses the same algorithm as the X Window System MouseKeysAccel feature. You can read more about it [on Wikipedia](https://en.wikipedia.org/wiki/Mouse_keys).
+Mousekeys is a feature that allows you to emulate a mouse using your keyboard. You can move the pointer around, click up to 5 buttons, and even scroll in all 4 directions.
 
-## Adding Mousekeys to a Keymap
+There are 2 ways to define how the mousekeys behave, using "[auto-accelerating](#configuring-the-behavior-of-mousekeys-with-auto-accelerated-movement)" or "[3-speed constant](#configuring-the-behavior-of-mousekeys-with-3-speed-constant-movement)" behavior.
 
-There are two steps to adding Mousekeys support to your keyboard. You must enable support in the `rules.mk` file and you must map mouse actions to keys on your keyboard.
+In either case, you will need to enable mousekeys in your makefile,
+and add the relevant [keycodes](#mapping-mouse-actions-to-keyboard-keys) to your keymap.
 
-### Adding Mousekeys Support in the `rules.mk`
+#### Enable Mousekeys
 
-To add support for Mousekeys you simply need to add a single line to your keymap's `rules.mk`:
+To enable the mousekey functionality, add the following line to your keymap's `rules.mk`:
 
 ```
 MOUSEKEY_ENABLE = yes
 ```
 
-You can see an example here: https://github.com/qmk/qmk_firmware/blob/master/keyboards/clueboard/66/keymaps/mouse_keys/rules.mk
-
-### Mapping Mouse Actions to Keyboard Keys
+#### Mapping Mouse Actions to Keyboard Keys
 
 You can use these keycodes within your keymap to map button presses to mouse actions:
 
-|Key             |Aliases  |Description                |
-|----------------|---------|---------------------------|
-|`KC_MS_UP`      |`KC_MS_U`|Mouse Cursor Up            |
-|`KC_MS_DOWN`    |`KC_MS_D`|Mouse Cursor Down          |
-|`KC_MS_LEFT`    |`KC_MS_L`|Mouse Cursor Left          |
-|`KC_MS_RIGHT`   |`KC_MS_R`|Mouse Cursor Right         |
-|`KC_MS_BTN1`    |`KC_BTN1`|Mouse Button 1             |
-|`KC_MS_BTN2`    |`KC_BTN2`|Mouse Button 2             |
-|`KC_MS_BTN3`    |`KC_BTN3`|Mouse Button 3             |
-|`KC_MS_BTN4`    |`KC_BTN4`|Mouse Button 4             |
-|`KC_MS_BTN5`    |`KC_BTN5`|Mouse Button 5             |
-|`KC_MS_WH_UP`   |`KC_WH_U`|Mouse Wheel Up             |
-|`KC_MS_WH_DOWN` |`KC_WH_D`|Mouse Wheel Down           |
-|`KC_MS_WH_LEFT` |`KC_WH_L`|Mouse Wheel Left           |
-|`KC_MS_WH_RIGHT`|`KC_WH_R`|Mouse Wheel Right          |
-|`KC_MS_ACCEL0`  |`KC_ACL0`|Set mouse acceleration to 0|
-|`KC_MS_ACCEL1`  |`KC_ACL1`|Set mouse acceleration to 1|
-|`KC_MS_ACCEL2`  |`KC_ACL2`|Set mouse acceleration to 2|
+|Key             |Aliases  |Description                        |
+|----------------|---------|-----------------------------------|
+|`KC_MS_UP`      |`KC_MS_U`|Mouse Cursor Up                    |
+|`KC_MS_DOWN`    |`KC_MS_D`|Mouse Cursor Down                  |
+|`KC_MS_LEFT`    |`KC_MS_L`|Mouse Cursor Left                  |
+|`KC_MS_RIGHT`   |`KC_MS_R`|Mouse Cursor Right                 |
+|`KC_MS_BTN1`    |`KC_BTN1`|Mouse Button 1                     |
+|`KC_MS_BTN2`    |`KC_BTN2`|Mouse Button 2                     |
+|`KC_MS_BTN3`    |`KC_BTN3`|Mouse Button 3                     |
+|`KC_MS_BTN4`    |`KC_BTN4`|Mouse Button 4                     |
+|`KC_MS_BTN5`    |`KC_BTN5`|Mouse Button 5                     |
+|`KC_MS_WH_UP`   |`KC_WH_U`|Mouse Wheel Up                     |
+|`KC_MS_WH_DOWN` |`KC_WH_D`|Mouse Wheel Down                   |
+|`KC_MS_WH_LEFT` |`KC_WH_L`|Mouse Wheel Left                   |
+|`KC_MS_WH_RIGHT`|`KC_WH_R`|Mouse Wheel Right                  |
+|`KC_MS_ACCEL0`  |`KC_ACL0`|Set mouse acceleration to 0(slow)  |
+|`KC_MS_ACCEL1`  |`KC_ACL1`|Set mouse acceleration to 1(medium)|
+|`KC_MS_ACCEL2`  |`KC_ACL2`|Set mouse acceleration to 2(fast)  |
 
-You can see an example in the `_ML` here: https://github.com/qmk/qmk_firmware/blob/master/keyboards/clueboard/66/keymaps/mouse_keys/keymap.c#L46
 
-## Configuring the Behavior of Mousekeys
+## Configuring the Behavior of Mousekeys with auto-accelerated movement
+
+This behavior is intended to emulate the X Window System MouseKeysAccel feature. You can read more about it [on Wikipedia](https://en.wikipedia.org/wiki/Mouse_keys).
 
 The default speed for controlling the mouse with the keyboard is intentionally slow. You can adjust these parameters by adding these settings to your keymap's `config.h` file. All times are specified in milliseconds (ms).
 
@@ -55,27 +55,60 @@ The default speed for controlling the mouse with the keyboard is intentionally s
 #define MOUSEKEY_WHEEL_TIME_TO_MAX 40
 ```
 
-
-### `MOUSEKEY_DELAY`
+#### `MOUSEKEY_DELAY`
 
 When one of the mouse movement buttons is pressed this setting is used to define the delay between that button press and the mouse cursor moving. Some people find that small movements are impossible if this setting is too low, while settings that are too high feel sluggish.
 
-### `MOUSEKEY_INTERVAL`
+#### `MOUSEKEY_INTERVAL`
 
 When a movement key is held down this specifies how long to wait between each movement report. Lower settings will translate into an effectively higher mouse speed.
 
-### `MOUSEKEY_MAX_SPEED`
+#### `MOUSEKEY_MAX_SPEED`
 
 As a movement key is held down the speed of the mouse cursor will increase until it reaches `MOUSEKEY_MAX_SPEED`.
 
-### `MOUSEKEY_TIME_TO_MAX`
+#### `MOUSEKEY_TIME_TO_MAX`
 
 How long you want to hold down a movement key for until `MOUSEKEY_MAX_SPEED` is reached. This controls how quickly your cursor will accelerate.
 
-### `MOUSEKEY_WHEEL_MAX_SPEED`
+#### `MOUSEKEY_WHEEL_MAX_SPEED`
 
 The top speed for scrolling movements.
 
-### `MOUSEKEY_WHEEL_TIME_TO_MAX`
+#### `MOUSEKEY_WHEEL_TIME_TO_MAX`
 
 How long you want to hold down a scroll key for until `MOUSEKEY_WHEEL_MAX_SPEED` is reached. This controls how quickly your scrolling will accelerate.
+
+
+## Configuring the Behavior of Mousekeys with 3-speed constant movement
+
+In your keymap's `config.h`, you must add the line:
+```
+#define MK_3_SPEED
+```
+Then you can precisely define 3 different speeds for both the cursor and the mouse wheel, and also whether speed selection is momentary or tap-to-select.
+For each speed, you can specify how many milliseconds you want between reports(interval), and how far you want to it to move per report(offset).
+
+For example:
+
+```
+#define MK_3_SPEED
+#define MK_MOMENTARY_ACCEL // comment this out for tap-to-select acceleration
+// cursor speeds:
+#define MK_C_OFFSET_SLOW     1 // pixels
+#define MK_C_INTERVAL_SLOW 100 // milliseconds
+#define MK_C_OFFSET_MED      4
+#define MK_C_INTERVAL_MED   16
+#define MK_C_OFFSET_FAST    12
+#define MK_C_INTERVAL_FAST  16
+// scroll wheel speeds:
+#define MK_W_OFFSET_SLOW     1 // wheel clicks
+#define MK_W_INTERVAL_SLOW 400 // milliseconds
+#define MK_W_OFFSET_MED      1
+#define MK_W_INTERVAL_MED  200
+#define MK_W_OFFSET_FAST     1
+#define MK_W_INTERVAL_FAST 100
+```
+
+Medium values will be used as the default or unmodified speed.
+The speed at which both the cursor and scrolling move can be selected with KC_ACL0, KC_ACL1, KC_ACL2 for slow, medium, and fast. However, if you leave MK_MOMENTARY_ACCEL defined then there is no need to ever send KC_ACL1, since that will be the unmodified speed.

docs/feature_rgb_matrix.md

@@ -10,39 +10,45 @@ If you want to use single color LED's you should use the [LED Matrix Subsystem](
 
 There is basic support for addressable RGB matrix lighting with the I2C IS31FL3731 RGB controller. To enable it, add this to your `rules.mk`:
 
-    RGB_MATRIX_ENABLE = IS31FL3731
+```C
+RGB_MATRIX_ENABLE = IS31FL3731
+```
 
 Configure the hardware via your `config.h`:
 
-	// This is a 7-bit address, that gets left-shifted and bit 0
-	// set to 0 for write, 1 for read (as per I2C protocol)
-	// The address will vary depending on your wiring:
-	// 0b1110100 AD <-> GND
-	// 0b1110111 AD <-> VCC
-	// 0b1110101 AD <-> SCL
-	// 0b1110110 AD <-> SDA
-	#define DRIVER_ADDR_1 0b1110100
-	#define DRIVER_ADDR_2 0b1110110
+```C
+// This is a 7-bit address, that gets left-shifted and bit 0
+// set to 0 for write, 1 for read (as per I2C protocol)
+// The address will vary depending on your wiring:
+// 0b1110100 AD <-> GND
+// 0b1110111 AD <-> VCC
+// 0b1110101 AD <-> SCL
+// 0b1110110 AD <-> SDA
+#define DRIVER_ADDR_1 0b1110100
+#define DRIVER_ADDR_2 0b1110110
 
-	#define DRIVER_COUNT 2
-	#define DRIVER_1_LED_TOTAL 25
-	#define DRIVER_2_LED_TOTAL 24
-	#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL
+#define DRIVER_COUNT 2
+#define DRIVER_1_LED_TOTAL 25
+#define DRIVER_2_LED_TOTAL 24
+#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL
+```
 
 Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.
 
 Define these arrays listing all the LEDs in your `<keyboard>.c`:
 
-	const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
-	/* Refer to IS31 manual for these locations
-	 *   driver
-	 *   |  R location
-	 *   |  |      G location
-	 *   |  |      |      B location
-	 *   |  |      |      | */
-	    {0, C1_3,  C2_3,  C3_3},
-	    ....
-	}
+```C
+const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
+/* Refer to IS31 manual for these locations
+    *   driver
+    *   |  R location
+    *   |  |      G location
+    *   |  |      |      B location
+    *   |  |      |      | */
+    {0, C1_3,  C2_3,  C3_3},
+    ....
+}
+```
 
 Where `Cx_y` is the location of the LED in the matrix defined by [the datasheet](http://www.issi.com/WW/pdf/31FL3731.pdf) and the header file `drivers/issi/is31fl3731.h`. The `driver` is the index of the driver you defined in your `config.h` (`0` or `1` right now).
 
@@ -50,60 +56,70 @@ Where `Cx_y` is the location of the LED in the matrix defined by [the datasheet]
 
 There is basic support for addressable RGB matrix lighting with the I2C IS31FL3733 RGB controller. To enable it, add this to your `rules.mk`:
 
-    RGB_MATRIX_ENABLE = IS31FL3733
+```C
+RGB_MATRIX_ENABLE = IS31FL3733
+```
 
 Configure the hardware via your `config.h`:
 
-	// This is a 7-bit address, that gets left-shifted and bit 0
-	// set to 0 for write, 1 for read (as per I2C protocol)
-	// The address will vary depending on your wiring:
-	// 00 <-> GND
-	// 01 <-> SCL
-	// 10 <-> SDA
-	// 11 <-> VCC
-	// ADDR1 represents A1:A0 of the 7-bit address.
-	// ADDR2 represents A3:A2 of the 7-bit address.
-	// The result is: 0b101(ADDR2)(ADDR1)
-	#define DRIVER_ADDR_1 0b1010000
-	#define DRIVER_ADDR_2 0b1010000 // this is here for compliancy reasons.
+```C
+// This is a 7-bit address, that gets left-shifted and bit 0
+// set to 0 for write, 1 for read (as per I2C protocol)
+// The address will vary depending on your wiring:
+// 00 <-> GND
+// 01 <-> SCL
+// 10 <-> SDA
+// 11 <-> VCC
+// ADDR1 represents A1:A0 of the 7-bit address.
+// ADDR2 represents A3:A2 of the 7-bit address.
+// The result is: 0b101(ADDR2)(ADDR1)
+#define DRIVER_ADDR_1 0b1010000
+#define DRIVER_ADDR_2 0b1010000 // this is here for compliancy reasons.
 
-	#define DRIVER_COUNT 2
-	#define DRIVER_1_LED_TOTAL 64
-	#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL
+#define DRIVER_COUNT 2
+#define DRIVER_1_LED_TOTAL 64
+#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL
+```
 
 Currently only a single drivers is supported, but it would be trivial to support all 4 combinations. For now define `DRIVER_ADDR_2` as `DRIVER_ADDR_1`
 
 Define these arrays listing all the LEDs in your `<keyboard>.c`:
 
-	const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
-	/* Refer to IS31 manual for these locations
-	 *   driver
-	 *   |  R location
-	 *   |  |       G location
-	 *   |  |       |       B location
-	 *   |  |       |       | */
-	    {0, B_1,    A_1,    C_1},
-	    ....
-	}
+```C
+const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
+/* Refer to IS31 manual for these locations
+    *   driver
+    *   |  R location
+    *   |  |       G location
+    *   |  |       |       B location
+    *   |  |       |       | */
+    {0, B_1,    A_1,    C_1},
+    ....
+}
+```
 
 Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](http://www.issi.com/WW/pdf/31FL3733.pdf) and the header file `drivers/issi/is31fl3733.h`. The `driver` is the index of the driver you defined in your `config.h` (Only `0` right now).
 
 From this point forward the configuration is the same for all the drivers. 
 
-	const rgb_led g_rgb_leds[DRIVER_LED_TOTAL] = {
-	/* {row | col << 4}
-	 *    |           {x=0..224, y=0..64}
-	 *    |              |               modifier
-	 *    |              |                 | */
-	    {{0|(0<<4)},   {20.36*0, 21.33*0}, 1},
-	    {{0|(1<<4)},   {20.36*1, 21.33*0}, 1},
-	    ....
-	}
+```C
+const rgb_led g_rgb_leds[DRIVER_LED_TOTAL] = {
+/*  {row | col << 4}
+    *    |         {x=0..224, y=0..64}
+    *    |            |              modifier
+    *    |            |                | */
+    {{0|(0<<4)},   {20.36*0, 21.33*0}, 1},
+    {{0|(1<<4)},   {20.36*1, 21.33*0}, 1},
+    ....
+}
+```
 
 The format for the matrix position used in this array is `{row | (col << 4)}`. The `x` is between (inclusive) 0-224, and `y` is between (inclusive) 0-64. The easiest way to calculate these positions is:
 
-    x = 224 / ( NUMBER_OF_COLS - 1 ) * ROW_POSITION
-    y = 64 / (NUMBER_OF_ROWS - 1 ) * COL_POSITION
+```C
+x = 224 / ( NUMBER_OF_COLS - 1 ) * ROW_POSITION
+y = 64 / (NUMBER_OF_ROWS - 1 ) * COL_POSITION
+```
 
 Where all variables are decimels/floats.
 
@@ -113,48 +129,50 @@ Where all variables are decimels/floats.
 
 All RGB keycodes are currently shared with the RGBLIGHT system:
 
-	* `RGB_TOG` - toggle
-	* `RGB_MOD` - cycle through modes
-	* `RGB_HUI` - increase hue
-	* `RGB_HUD` - decrease hue
-	* `RGB_SAI` - increase saturation
-	* `RGB_SAD` - decrease saturation
-	* `RGB_VAI` - increase value
-	* `RGB_VAD` - decrease value
-	* `RGB_SPI` - increase speed effect (no EEPROM support)
-	* `RGB_SPD` - decrease speed effect (no EEPROM support)
-
-
-	* `RGB_MODE_*` keycodes will generally work, but are not currently mapped to the correct effects for the RGB Matrix system
+* `RGB_TOG` - toggle
+* `RGB_MOD` - cycle through modes
+* `RGB_HUI` - increase hue
+* `RGB_HUD` - decrease hue
+* `RGB_SAI` - increase saturation
+* `RGB_SAD` - decrease saturation
+* `RGB_VAI` - increase value
+* `RGB_VAD` - decrease value
+* `RGB_SPI` - increase speed effect (no EEPROM support)
+* `RGB_SPD` - decrease speed effect (no EEPROM support)
+* `RGB_MODE_*` keycodes will generally work, but are not currently mapped to the correct effects for the RGB Matrix system
 
 ## RGB Matrix Effects
 
-These are the effects that are currently available:
+All effects have been configured to support current configuration values (Hue, Saturation, Value, & Speed) unless otherwise noted below. These are the effects that are currently available:
 
-	enum rgb_matrix_effects {
-	    RGB_MATRIX_SOLID_COLOR = 1,
-	    RGB_MATRIX_ALPHAS_MODS,
-	    RGB_MATRIX_DUAL_BEACON,
-	    RGB_MATRIX_GRADIENT_UP_DOWN,
-	    RGB_MATRIX_RAINDROPS,
-	    RGB_MATRIX_CYCLE_ALL,
-	    RGB_MATRIX_CYCLE_LEFT_RIGHT,
-	    RGB_MATRIX_CYCLE_UP_DOWN,
-	    RGB_MATRIX_RAINBOW_BEACON,
-	    RGB_MATRIX_RAINBOW_PINWHEELS,
-	    RGB_MATRIX_RAINBOW_MOVING_CHEVRON,
-	    RGB_MATRIX_JELLYBEAN_RAINDROPS,
-	    RGB_MATRIX_DIGITAL_RAIN,
-	#ifdef RGB_MATRIX_KEYPRESSES
-	    RGB_MATRIX_SOLID_REACTIVE,
-	    RGB_MATRIX_REACTIVE_SIMPLE,
-	    RGB_MATRIX_SPLASH,
-	    RGB_MATRIX_MULTISPLASH,
-	    RGB_MATRIX_SOLID_SPLASH,
-	    RGB_MATRIX_SOLID_MULTISPLASH,
-	#endif
-	    RGB_MATRIX_EFFECT_MAX
-	};
+```C
+enum rgb_matrix_effects {
+    RGB_MATRIX_NONE = 0,
+    RGB_MATRIX_SOLID_COLOR = 1,     // Static single hue, no speed support
+    RGB_MATRIX_ALPHAS_MODS,         // Static dual hue, speed is hue for secondary hue
+    RGB_MATRIX_GRADIENT_UP_DOWN,    // Static gradient top to bottom, speed controls how much gradient changes
+    RGB_MATRIX_BREATHING,           // Single hue brightness cycling animation
+    RGB_MATRIX_CYCLE_ALL,           // Full keyboard solid hue cycling through full gradient
+    RGB_MATRIX_CYCLE_LEFT_RIGHT,    // Full gradient scrolling left to right 
+    RGB_MATRIX_CYCLE_UP_DOWN,       // Full gradient scrolling top to bottom
+    RGB_MATRIX_RAINBOW_MOVING_CHEVRON,  // Full gradent Chevron shapped scrolling left to right
+    RGB_MATRIX_DUAL_BEACON,         // Full gradient spinning around center of keyboard
+    RGB_MATRIX_RAINBOW_BEACON,      // Full tighter gradient spinning around center of keyboard
+    RGB_MATRIX_RAINBOW_PINWHEELS,   // Full dual gradients spinning two halfs of keyboard
+    RGB_MATRIX_RAINDROPS,           // Randomly changes a single key's hue
+    RGB_MATRIX_JELLYBEAN_RAINDROPS, // Randomly changes a single key's hue and saturation
+    RGB_MATRIX_DIGITAL_RAIN,        // That famous computer simulation
+#if defined(RGB_MATRIX_KEYPRESSES) || defined(RGB_MATRIX_KEYRELEASES)
+    RGB_MATRIX_SOLID_REACTIVE_SIMPLE,   // Pulses keys hit to hue & value then fades value out
+    RGB_MATRIX_SOLID_REACTIVE,      // Static single hue, pulses keys hit to shifted hue then fades to current hue
+    RGB_MATRIX_SPLASH,              // Full gradient & value pulse away from a single key hit then fades value out
+    RGB_MATRIX_MULTISPLASH,         // Full gradient & value pulse away from multiple key hits then fades value out
+    RGB_MATRIX_SOLID_SPLASH,        // Hue & value pulse away from a single key hit then fades value out
+    RGB_MATRIX_SOLID_MULTISPLASH,   // Hue & value pulse away from multiple key hits then fades value out
+#endif
+    RGB_MATRIX_EFFECT_MAX
+};
+```
     
 You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `config.h`:
 
@@ -162,19 +180,20 @@ You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `con
 |Define                                             |Description                                 |
 |---------------------------------------------------|--------------------------------------------|
 |`#define DISABLE_RGB_MATRIX_ALPHAS_MODS`           |Disables `RGB_MATRIX_ALPHAS_MODS`           |
-|`#define DISABLE_RGB_MATRIX_DUAL_BEACON`           |Disables `RGB_MATRIX_DUAL_BEACON`           |
 |`#define DISABLE_RGB_MATRIX_GRADIENT_UP_DOWN`      |Disables `RGB_MATRIX_GRADIENT_UP_DOWN`      |
-|`#define DISABLE_RGB_MATRIX_RAINDROPS`             |Disables `RGB_MATRIX_RAINDROPS`             |
+|`#define DISABLE_RGB_MATRIX_BREATHING`             |Disables `RGB_MATRIX_BREATHING`             |
 |`#define DISABLE_RGB_MATRIX_CYCLE_ALL`             |Disables `RGB_MATRIX_CYCLE_ALL`             |
 |`#define DISABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT`      |Disables `RGB_MATRIX_CYCLE_LEFT_RIGHT`      |
 |`#define DISABLE_RGB_MATRIX_CYCLE_UP_DOWN`         |Disables `RGB_MATRIX_CYCLE_UP_DOWN`         |
+|`#define DISABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON`|Disables `RGB_MATRIX_RAINBOW_MOVING_CHEVRON`|
+|`#define DISABLE_RGB_MATRIX_DUAL_BEACON`           |Disables `RGB_MATRIX_DUAL_BEACON`           |
 |`#define DISABLE_RGB_MATRIX_RAINBOW_BEACON`        |Disables `RGB_MATRIX_RAINBOW_BEACON`        |
 |`#define DISABLE_RGB_MATRIX_RAINBOW_PINWHEELS`     |Disables `RGB_MATRIX_RAINBOW_PINWHEELS`     |
-|`#define DISABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON`|Disables `RGB_MATRIX_RAINBOW_MOVING_CHEVRON`|
+|`#define DISABLE_RGB_MATRIX_RAINDROPS`             |Disables `RGB_MATRIX_RAINDROPS`             |
 |`#define DISABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS`   |Disables `RGB_MATRIX_JELLYBEAN_RAINDROPS`   |
 |`#define DISABLE_RGB_MATRIX_DIGITAL_RAIN`          |Disables `RGB_MATRIX_DIGITAL_RAIN`          |
 |`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE`        |Disables `RGB_MATRIX_SOLID_REACTIVE`        |
-|`#define DISABLE_RGB_MATRIX_REACTIVE_SIMPLE`       |Disables `RGB_MATRIX_REACTIVE_SIMPLE`       |
+|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE` |Disables `RGB_MATRIX_SOLID_REACTIVE_SIMPLEE`|
 |`#define DISABLE_RGB_MATRIX_SPLASH`                |Disables `RGB_MATRIX_SPLASH`                |
 |`#define DISABLE_RGB_MATRIX_MULTISPLASH`           |Disables `RGB_MATRIX_MULTISPLASH`           |
 |`#define DISABLE_RGB_MATRIX_SOLID_SPLASH`          |Disables `RGB_MATRIX_SOLID_SPLASH`          |
@@ -185,26 +204,33 @@ You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `con
 
 Custom layer effects can be done by defining this in your `<keyboard>.c`:
 
-    void rgb_matrix_indicators_kb(void) {
-        rgb_matrix_set_color(index, red, green, blue);
-    }
+```C
+void rgb_matrix_indicators_kb(void) {
+    rgb_matrix_set_color(index, red, green, blue);
+}
+```
 
 A similar function works in the keymap as `rgb_matrix_indicators_user`.
 
 ## Additional `config.h` Options
 
-	#define RGB_MATRIX_KEYPRESSES // reacts to keypresses (will slow down matrix scan by a lot)
-	#define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (not recommened)
-	#define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
-	#define RGB_DISABLE_WHEN_USB_SUSPENDED false // turn off effects when suspended
-    #define RGB_MATRIX_SKIP_FRAMES 1 // number of frames to skip when displaying animations (0 is full effect) if not defined defaults to 1
-    #define RGB_MATRIX_MAXIMUM_BRIGHTNESS 200 // limits maximum brightness of LEDs to 200 out of 255. If not defined maximum brightness is set to 255
+```C
+#define RGB_MATRIX_KEYPRESSES // reacts to keypresses
+#define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (instead of keypresses)
+#define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
+#define RGB_DISABLE_WHEN_USB_SUSPENDED false // turn off effects when suspended
+#define RGB_MATRIX_LED_PROCESS_LIMIT (DRIVER_LED_TOTAL + 4) / 5 // limits the number of LEDs to process in an animation per task run (increases keyboard responsiveness)
+#define RGB_MATRIX_LED_FLUSH_LIMIT 16 // limits in milliseconds how frequently an animation will update the LEDs. 16 (16ms) is equivalent to limiting to 60fps (increases keyboard responsiveness)
+#define RGB_MATRIX_MAXIMUM_BRIGHTNESS 200 // limits maximum brightness of LEDs to 200 out of 255. If not defined maximum brightness is set to 255
+```
 
 ## EEPROM storage
 
 The EEPROM for it is currently shared with the RGBLIGHT system (it's generally assumed only one RGB would be used at a time), but could be configured to use its own 32bit address with:
 
-    #define EECONFIG_RGB_MATRIX (uint32_t *)16
+```C
+#define EECONFIG_RGB_MATRIX (uint32_t *)16
+```
 
 Where `16` is an unused index from `eeconfig.h`.
 
@@ -212,12 +238,14 @@ Where `16` is an unused index from `eeconfig.h`.
 
 To use the suspend feature, add this to your `<keyboard>.c`:
 
-	void suspend_power_down_kb(void)
-	{
-	    rgb_matrix_set_suspend_state(true);
-	}
+```C
+void suspend_power_down_kb(void)
+{
+    rgb_matrix_set_suspend_state(true);
+}
 
-	void suspend_wakeup_init_kb(void)
-	{
-	    rgb_matrix_set_suspend_state(false);
-	}
+void suspend_wakeup_init_kb(void)
+{
+    rgb_matrix_set_suspend_state(false);
+}
+```

docs/feature_rgblight.md

@@ -23,10 +23,11 @@ RGBLIGHT_ENABLE = yes
 
 At minimum you must define the data pin your LED strip is connected to, and the number of LEDs in the strip, in your `config.h`. If your keyboard has onboard RGB LEDs, and you are simply creating a keymap, you usually won't need to modify these.
 
-|Define      |Description                                  |
-|------------|---------------------------------------------|
-|`RGB_DI_PIN`|The pin connected to the data pin of the LEDs|
-|`RGBLED_NUM`|The number of LEDs connected                 |
+|Define         |Description                                                                                              |
+|---------------|---------------------------------------------------------------------------------------------------------|
+|`RGB_DI_PIN`   |The pin connected to the data pin of the LEDs                                                            |
+|`RGBLED_NUM`   |The number of LEDs connected                                                                             |
+|`RGBLED_SPLIT` |(Optional) For split keyboards, the number of LEDs connected on each half directly wired to `RGB_DI_PIN` |
 
 Then you should be able to use the keycodes below to change the RGB lighting to your liking.
 
@@ -124,6 +125,8 @@ The following options can be used to tweak the various animations:
 
 You can also modify the speeds that the different modes animate at:
 
+Here is a quick demo on Youtube (with NPKC KC60) (https://www.youtube.com/watch?v=VKrpPAHlisY).
+
 ```c
 // How long (in milliseconds) to wait between animation steps for each of the "Solid color breathing" animations
 const uint8_t RGBLED_BREATHING_INTERVALS[] PROGMEM = {30, 20, 10, 5};
@@ -188,6 +191,53 @@ If you need to change your RGB lighting in code, for example in a macro to chang
 
 Additionally, [`rgblight_list.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight_list.h) defines several predefined shortcuts for various colors. Feel free to add to this list!
 
+## Changing the order of the LEDs
+
+If you want to make the logical order of LEDs different from the electrical connection order, you can do this by defining the `RGBLIGHT_LED_MAP` macro in your `config.h`.
+
+By defining `RGBLIGHT_LED_MAP` as in the example below, you can specify the LED with addressing in reverse order of the electrical connection order.
+
+```c
+// config.h
+
+#define RGBLED_NUM 10
+#define RGBLIGHT_LED_MAP { 9, 8, 7, 6, 5, 4, 3, 2, 1, 0 }
+
+```
+
+For keyboards that use the RGB LEDs as a backlight for each key, you can also define it as in the example below.
+
+```c
+// config.h
+
+#define RGBLED_NUM 30
+
+/* RGB LED Conversion macro from physical array to electric array */
+#define LED_LAYOUT( \
+    L00, L01, L02, L03, L04, L05,  \
+    L10, L11, L12, L13, L14, L15,  \
+    L20, L21, L22, L23, L24, L25,  \
+    L30, L31, L32, L33, L34, L35,  \
+    L40, L41, L42, L43, L44, L45 ) \
+  { \
+    L05, L04, L03, L02, L01, L00,   \
+    L10, L11, L12, L13, L14, L15,   \
+    L25, L24, L23, L22, L21, L20,   \
+    L30, L31, L32, L33, L34, L35,   \
+    L46, L45, L44, L43, L42, L41    \
+  }
+
+/* RGB LED logical order map */
+/* Top->Bottom, Right->Left */
+#define RGBLIGHT_LED_MAP LED_LAYOUT( \
+  25, 20, 15, 10,  5,  0,       \
+  26, 21, 16, 11,  6,  1,       \
+  27, 22, 17, 12,  7,  2,       \
+  28, 23, 18, 13,  8,  3,       \
+  29, 24, 19, 14,  9,  4 )
+
+```
+
 ## Hardware Modification
 
 If your keyboard lacks onboard underglow LEDs, you may often be able to solder on an RGB LED strip yourself. You will need to find an unused pin to wire to the data pin of your LED strip. Some keyboards may break out unused pins from the MCU to make soldering easier. The other two pins, VCC and GND, must also be connected to the appropriate power pins.

docs/flashing.md

@@ -60,7 +60,7 @@ There are a number of DFU commands that you can use to flash firmware to a DFU d
 
 ## Caterina
 
-Arduino boards and their clones use the [Caterina bootloader](https://github.com/arduino/Arduino/tree/master/hardware/arduino/avr/bootloaders/caterina) (any keyboard built with a Pro Micro, or clone), and uses the avr109 protocol to communicate through virtual serial. Bootloaders like [A-Star](https://www.pololu.com/docs/0J61/9) are based on Caterina.
+Arduino boards and their clones use the [Caterina bootloader](https://github.com/arduino/ArduinoCore-avr/tree/master/bootloaders/caterina) (any keyboard built with a Pro Micro, or clone), and uses the avr109 protocol to communicate through virtual serial. Bootloaders like [A-Star](https://www.pololu.com/docs/0J61/9) are based on Caterina.
 
 To ensure compatibility with the Caterina bootloader, make sure this block is present your `rules.mk`:
 

docs/getting_started_build_tools.md

@@ -2,6 +2,8 @@
 
 This page describes setting up the build environment for QMK. These instructions cover AVR processors (such as the atmega32u4).
 
+After cloning the repo of QMK run `make git-submodule` once to download 3rd party libraries like ChibiOS.
+
 <!-- FIXME: We should have ARM instructions somewhere. -->
 
 Note: If it is your first time here, Check out the "Complete Newbs guide" instead

docs/isp_flashing_guide.md

@@ -63,6 +63,7 @@ If you just want to get things back to normal, you can flash only a bootloader f
 
 * [`atmega32u4`](https://github.com/qmk/qmk_firmware/blob/master/util/bootloader_atmega32u4_1_0_0.hex) - Most keyboards, Planck Rev 1-5, Preonic Rev 1-2
 * [`at90usb1286`](https://github.com/qmk/qmk_firmware/blob/master/util/bootloader_at90usb128x_1_0_1.hex) - Planck Light Rev 1
+* [`atmega32a`](https://github.com/qmk/qmk_firmware/blob/master/util/bootloader_atmega32a_1_0_0.hex) - jj40
 
 If you're not sure what your board uses, look in the `rules.mk` file for the keyboard in QMK. The `MCU =` line will have the value you need. It may differ between different versions of the board.
 
@@ -113,6 +114,10 @@ Since our keyboard uses an `atmega32u4` (common), that is the chip we'll specify
 
     avrdude -c avrisp -P COM3 -p atmega32u4 -U flash:w:main.hex:i
 
+If your board uses an `atmega32a` (e.g. on a jj40), the command is this (the extra code at the end sets the fuses correctly):
+
+	avrdude -c avrisp -P COM3 -p atmega32 -U flash:w:main.hex:i -U hfuse:w:0xD0:m -U lfuse:w:0x0F:m
+
 You should see a couple of progress bars, then you should see:
 
     avrdude: verifying ...

keyboards/1upkeyboards/1up60hse/keymaps/default/keymap.c

@@ -22,7 +22,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
     KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT,
     KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT,
-    KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, MO(1), KC_LCTL
+    KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, MO(1), KC_RCTL
   ),
 
   [1] = LAYOUT_60_ansi(

keyboards/1upkeyboards/1up60hte/keymaps/default/keymap.c

@@ -21,9 +21,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 		KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,     KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSLS, KC_GRV,
 		KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,     KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSPC,
 		KC_LCTL, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,     KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
-		KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM,  KC_DOT,  KC_SLSH, KC_LSFT, MO(1),
-		KC_LCTL, KC_LALT, KC_LGUI, KC_SPC,  KC_LGUI, KC_LALT, KC_LCTL),
-		
+		KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM,  KC_DOT,  KC_SLSH, KC_RSFT, MO(1),
+		KC_LCTL, KC_LALT, KC_LGUI, KC_SPC,  KC_RGUI, KC_RALT, KC_RCTL),
+
 	[1] = LAYOUT_tsangan(
 		RESET,   KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,    KC_F10,  KC_F11,  KC_F12,  KC_INS, KC_DEL,
 		KC_CAPS, BL_TOGG, BL_DEC,  BL_INC,  BL_STEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_SLCK,  KC_PAUS, KC_UP,   KC_TRNS, KC_CLR,

keyboards/1upkeyboards/1up60hte/keymaps/hhkb/keymap.c

@@ -21,9 +21,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 		KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,     KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSLS, KC_GRV,
 		KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,     KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSPC,
 		KC_LCTL, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,     KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
-		KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM,  KC_DOT,  KC_SLSH, KC_LSFT, MO(1),
-		KC_NO,   KC_LALT, KC_LGUI, KC_SPC,  KC_LGUI, KC_LALT, KC_NO),
-		
+		KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM,  KC_DOT,  KC_SLSH, KC_RSFT, MO(1),
+		KC_NO,   KC_LALT, KC_LGUI, KC_SPC,  KC_RGUI, KC_RALT, KC_NO),
+
 	[1] = LAYOUT_tsangan(
 		RESET,   KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,    KC_F10,  KC_F11,  KC_F12,  KC_INS, KC_DEL,
 		KC_CAPS, BL_TOGG, BL_DEC,  BL_INC,  BL_STEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_SLCK,  KC_PAUS, KC_UP,   KC_TRNS, KC_CLR,

keyboards/1upkeyboards/1up60rgb/keymaps/default/keymap.c

@@ -1,4 +1,4 @@
-#include "1up60rgb.h"
+#include QMK_KEYBOARD_H
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 

keyboards/1upkeyboards/sweet16/keymaps/default/keymap.c

@@ -1,4 +1,4 @@
-#include "sweet16.h"
+#include QMK_KEYBOARD_H
 
 enum custom_keycodes {
   UP_URL = SAFE_RANGE

keyboards/40percentclub/half_n_half/keymaps/Boy_314/config.h

@@ -19,4 +19,4 @@
 // place overrides here
 #define IGNORE_MOD_TAP_INTERRUPT
 #define PERMISSIVE_HOLD
-#define TAPPING_TERM 200
+#define TAPPING_TERM 200

keyboards/40percentclub/half_n_half/keymaps/Boy_314/keymap.c

@@ -21,10 +21,17 @@ enum {
 };
 
 enum layers {
-	DVORAK,
-	QWERTY,
-	LOWER,
-	RAISE
+	_DVORAK,
+	_QWERTY,
+	_LOWER,
+	_RAISE,
+};
+
+enum halfnhalf_keycodes {
+	NEWTAB = SAFE_RANGE,
+	ALTF4,
+	CLSTAB,
+	PRVWIN,
 };
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
@@ -36,78 +43,78 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
 	 * |LShift|;     |Q     |J     |K     |X     |LAlt  |-     |B     |M     |W     |V     |Z     |RShift|
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
-	 *                             |TD Swap Layer|             |Space        |      
-	 *                             `-------------'             `-------------'
+	 *                             |TD Swap Layer|             |Space        |
+	 *                             `-------------'			       `-------------'
 	 */
-	[DVORAK] = LAYOUT(/* Base Dvorak */
-	  KC_TAB,           KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_BRIU, KC_EQL,     KC_F, KC_G, KC_C,    KC_R,   KC_L,   KC_BSPC, 
-	  LCTL_T(KC_CAPS),  KC_A,    KC_O,    KC_E,   KC_U, KC_I, KC_BRID, LCTL(KC_F), KC_D, KC_H, KC_T,    KC_N,   KC_S,   KC_ENT, 
-	  KC_LSPO,          KC_SCLN, KC_Q,    KC_J,   KC_K, KC_X, KC_LALT, KC_MINS,    KC_B, KC_M, KC_W,    KC_V,   KC_Z,   KC_RSPC, 
-	                                      TD(TD_SWAP_LAYERS),                      KC_SPC
+	[_DVORAK] = LAYOUT(/* Base Dvorak */
+	  KC_TAB,           KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_BRIU, KC_EQL,     KC_F, KC_G, KC_C,    KC_R,   KC_L,   KC_BSPC,
+	  LCTL_T(KC_CAPS),  KC_A,    KC_O,    KC_E,   KC_U, KC_I, KC_BRID, LCTL(KC_F), KC_D, KC_H, KC_T,    KC_N,   KC_S,   KC_ENT,
+	  KC_LSPO,          KC_SCLN, KC_Q,    KC_J,   KC_K, KC_X, KC_LALT, KC_MINS,    KC_B, KC_M, KC_W,    KC_V,   KC_Z,   KC_RSPC,
+	                                              TD(TD_SWAP_LAYERS),                    KC_SPC
 	),
-	
+
 	/* QWERTY
 	 * ,-------------------------------------------------------------------------------------------------.
 	 * |Tab   |Q     |W     |E     |R     |T     |Brght+|'     |Y     |U     |I     |O     |P     |Bksp  |
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
-	 * |LCtrl |A     |S     |D     |F     |G     |Brght-|Ctrl+F|H     |J     |K     |L     |;     |Enter |
+	 * |CtlCps|A     |S     |D     |F     |G     |Brght-|Ctrl+F|H     |J     |K     |L     |;     |Enter |
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
 	 * |LShift|Z     |X     |C     |V     |B     |LAlt  |-     |N     |M     |,     |.     |/     |RShift|
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
-	 *                             |TD Swap Layer|             |Space        |      
-	 *                             `-------------'             `-------------'
+	 *                             |TD Swap Layer|             |Space        |
+	 *                             `-------------'			       `-------------'
 	 */
-	[QWERTY] = LAYOUT(/* Base Qwerty */
-	  KC_TAB,   KC_Q,    KC_W,    KC_E,   KC_R, KC_T, KC_BRIU, KC_QUOT,    KC_Y, KC_U, KC_I,    KC_O,   KC_P,    KC_BSPC, 
-	  KC_LCTL,  KC_A,    KC_S,    KC_D,   KC_F, KC_G, KC_BRID, LCTL(KC_F), KC_H, KC_J, KC_K,    KC_L,   KC_SCLN, KC_ENT, 
-	  KC_LSPO,  KC_Z,    KC_X,    KC_C,   KC_V, KC_B, KC_LALT, KC_MINS,    KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSPC, 
-	                                      TD(TD_SWAP_LAYERS),                    KC_SPC
+	[_QWERTY] = LAYOUT(/* Base Qwerty */
+	  KC_TAB,           KC_Q,    KC_W,    KC_E,   KC_R, KC_T, KC_BRIU, KC_QUOT,    KC_Y, KC_U, KC_I,    KC_O,   KC_P,    KC_BSPC,
+	  LCTL_T(KC_CAPS),  KC_A,    KC_S,    KC_D,   KC_F, KC_G, KC_BRID, LCTL(KC_F), KC_H, KC_J, KC_K,    KC_L,   KC_SCLN, KC_ENT,
+	  KC_LSPO,          KC_Z,    KC_X,    KC_C,   KC_V, KC_B, KC_LALT, KC_MINS,    KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSPC,
+	                                              TD(TD_SWAP_LAYERS),                    KC_SPC
 	),
-	
+
 	/* LOWER
 	 * ,-------------------------------------------------------------------------------------------------.
-	 * |Esc   |1     |2     |3     |4     |5     |      |=     |6     |7     |8     |9     |0     |/     |
+	 * |Esc   |1     |2     |3     |4     |5     |      |      |6     |7     |8     |9     |0     |/     |
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
 	 * |Caps  |F1    |F2    |F3    |F4    |F5    |F6    |Vol Up|Play  |_     |+     |{     |}     ||     |
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
 	 * |      |F7    |F8    |F9    |F10   |F11   |F12   |Vol Dn|Next  |Home  |PgDn  |PgUp  |End   |      |
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
-	 *                             |             |             |             |      
+	 *                             |             |             |             |
 	 *                             `-------------'             `-------------'
 	 */
-	[LOWER] = LAYOUT(/* Numbers, Function Row, Media Control, Shifted Symbols, Dvorak Slash Key */
-	  KC_GESC, KC_1,  KC_2,  KC_3,  KC_4,   KC_5,   KC_TRNS, KC_TRNS, KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_SLSH, 
-	  KC_CAPS, KC_F1, KC_F2, KC_F3, KC_F4,  KC_F5,  KC_F6,   KC_VOLU, KC_MPLY, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE, 
+	[_LOWER] = LAYOUT(/* Numbers, Function Row, Media Control, Shifted Symbols, Dvorak Slash Key */
+	  KC_GESC, KC_1,  KC_2,  KC_3,  KC_4,   KC_5,   KC_TRNS, KC_TRNS, KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_SLSH,
+	  KC_CAPS, KC_F1, KC_F2, KC_F3, KC_F4,  KC_F5,  KC_F6,   KC_VOLU, KC_MPLY, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE,
 	  KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12,  KC_VOLD, KC_MNXT, KC_HOME, KC_PGDN, KC_PGUP, KC_END,  KC_TRNS,
-									KC_TRNS,    					           KC_TRNS
+									                KC_TRNS,    					            KC_TRNS
 	),
-	
+
 	/* RAISE
 	 * ,-------------------------------------------------------------------------------------------------.
-	 * |Reset |      |      |Up    |      |      |      |      |      |      |      |      |      |Del   |
+	 * |Reset |      |      |Up    |      |      |      |PRVWIN|CLSTAB|      |      |      |      |Del   |
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
-	 * |`     |      |Left  |Down  |Right |      |      |      |      |-     |=     |[     |]     |\     |
+	 * |`     |      |Left  |Down  |Right |      |      |NEWTAB|ALTF4 |-     |=     |[     |]     |\     |
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
 	 * |      |!     |@     |#     |$     |%     |      |      |^     |&     |*     |(     |)     |      |
 	 * |------+------+------+------+------+------+------+------+------+------+------+------+------+------|
-	 *                             |             |             |             |      
+	 *                             |             |             |             |
 	 *                             `-------------'             `-------------'
 	 */
-	[RAISE] = LAYOUT(/* Arrows, Shifted Numbers, Symbols, Delete, Reset Key */
-	  RESET,   KC_TRNS, KC_TRNS, KC_UP,   KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_DEL,
-	  KC_GRV,  KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_BSLS, 
-	  KC_TRNS, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_TRNS, KC_TRNS, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_TRNS, 
-										  KC_TRNS, 									   KC_TRNS
+	[_RAISE] = LAYOUT(/* Arrows, Shifted Numbers, Symbols, Delete, Macros */
+	  RESET,   KC_TRNS, KC_TRNS, KC_UP,   KC_TRNS, KC_TRNS, KC_TRNS, PRVWIN,  CLSTAB,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_DEL,
+	  KC_GRV,  KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, NEWTAB,  ALTF4,   KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_BSLS,
+	  KC_TRNS, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_TRNS, KC_TRNS, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_TRNS,
+										                    KC_TRNS,                            KC_TRNS
 	)
 };
 
 void tap_dance_choose_layer (qk_tap_dance_state_t *state, void *user_data) {
 	switch (state->count) {
 		case 1:
-			layer_on(LOWER);
+			layer_on(_LOWER);
 			break;
 		case 2:
-			layer_on(RAISE);
+			layer_on(_RAISE);
 			break;
 	}
 }
@@ -115,27 +122,52 @@ void tap_dance_choose_layer (qk_tap_dance_state_t *state, void *user_data) {
 void tap_dance_choose_layer_reset (qk_tap_dance_state_t *state, void *user_data) {
 	switch (state->count) {
 		case 1:
-			layer_off(LOWER);
+			layer_off(_LOWER);
 			break;
 		case 2:
-			layer_off(RAISE);
+			layer_off(_RAISE);
 			break;
 		case 3:
-			if (default_layer_state == DVORAK) {
-				default_layer_set(QWERTY);
-				layer_on(QWERTY);
-				layer_off(DVORAK);
+			if (biton32(default_layer_state) == _DVORAK) {
+				set_single_persistent_default_layer(_QWERTY);
 			}
-			else if (default_layer_state == QWERTY) {
-				default_layer_set(DVORAK);
-				layer_on(DVORAK);
-				layer_off(QWERTY);
+			else if (biton32(default_layer_state) == _QWERTY) {
+				set_single_persistent_default_layer(_DVORAK);
 			}
 			break;
 	}
 }
 
 qk_tap_dance_action_t tap_dance_actions[] = {
-	// ACTION_TAP_DANCE_FN_ADVANCED(on_each_tap_fn, on_dance_finished_fn, on_dance_reset_fn)
 	[TD_SWAP_LAYERS] = ACTION_TAP_DANCE_FN_ADVANCED(NULL, tap_dance_choose_layer, tap_dance_choose_layer_reset)
-};
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+	switch (keycode) {
+		// Control + T
+		case NEWTAB:
+			if (record->event.pressed) {
+				SEND_STRING(SS_LCTRL("t"));
+			}
+			break;
+		// Alt + F4
+		case ALTF4:
+			if (record->event.pressed) {
+				SEND_STRING(SS_DOWN(X_LALT)SS_TAP(X_F4)SS_UP(X_LALT));
+			}
+			break;
+		// Control + W
+		case CLSTAB:
+			if (record->event.pressed) {
+				SEND_STRING(SS_LCTRL("w"));
+			}
+			break;
+		// Control + Shift + N
+		case PRVWIN:
+			if (record->event.pressed) {
+				SEND_STRING(SS_LCTRL(SS_LSFT("n")));
+			}
+			break;
+	}
+	return true;
+}

keyboards/40percentclub/mf68/keymaps/default/keymap.c

@@ -3,51 +3,29 @@
 #define _QWERTY 0
 #define _FN1 1
 #define _FN2 2
-#define KC_ KC_TRNS
-#define KC_X0 LT(_FN2, KC_GRV)
-#define KC_X1 MO(_FN1)
-#define KC_X2 BL_STEP
+
+#define FN2_GRV LT(_FN2, KC_GRV)
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-  [_QWERTY] = LAYOUT_kc(
- /*,----+----+----+----+----+----+----+----+----+----+----+----+----+--------.  ,----+----. */
-    ESC , 1  , 2  , 3  , 4  , 5  , 6  , 7  , 8  , 9  , 0  ,MINS,EQL ,  BSPC  ,   INS ,PGUP,
- /*|----`----`----`----`----`----`----`----`----`----`----`----`----`--------|  |----`----| */
-    TAB   , Q  , W  , E  , R  , T  , Y  , U  , I  , O  , P  ,LBRC,RBRC, BSLS ,   DEL ,PGDN,
- /*|------`----`----`----`----`----`----`----`----`----`----`----`----`------|  `----`----' */
-    X0     , A  , S  , D  , F  , G  , H  , J  , K  , L  ,SCLN,QUOT,    ENTER ,
- /*|-------`----`----`----`----`----`----`----`----`----`----`----`----------|  ,----. */
-    LSFT     , Z  , X  , C  , V  , B  , N  , M  ,COMM,DOT ,SLSH,       RSFT  ,    UP ,
- /*|---------`----`----`----`----`----`----`----`----`----`----`-------------.--|----|----. */
-    LCTL ,LGUI ,LALT ,            SPACE             ,  X1  ,RALT ,RCTL ,    LEFT,DOWN,RGHT
- /*`-----+-----+-----+------------------------------+------+-----+-----'   `----+----+----' */
+  [_QWERTY] = LAYOUT_68_ansi(
+    KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,          KC_INS,  KC_PGUP,
+    KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,          KC_DEL,  KC_PGDN,
+    FN2_GRV, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,          KC_ENT,
+    KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,                   KC_RSFT,          KC_UP,
+    KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             MO(1),   KC_RALT, KC_RCTL,          KC_LEFT, KC_DOWN, KC_RGHT
   ),
-
-  [_FN1] = LAYOUT_kc(
- /*,----+----+----+----+----+----+----+----+----+----+----+----+----+--------.  ,----+----. */
-    GRV , F1 , F2 , F3 , F4 , F5 , F6 , F7 , F8 , F9 ,F10 ,F11 ,F12 ,   BSPC ,   VOLU,HOME,
- /*|esc-`-1--`-2--`-3--`-4--`-5--`-6--`-7--`-8--`-9--`-0--`mnus`plus`--bksp--|  |ins-`pgup| */
-          ,    ,    , UP ,    ,    ,    ,    ,    ,    ,    ,    , X2 ,      ,   VOLD,END,
- /*|tab---`-q--`-w--`-e--`-r--`-t--`-y--`-u--`-i--`-o--`-p--`-{--`-}--`--|---|  `del-`pgdn' */
-           ,    ,LEFT,DOWN,RGHT,    ,    ,    ,    ,    ,    ,    ,          ,
- /*|caps---`-a--`-s--`-d--`-f--`-g--`-h--`-j--`-k--`-l--`-;--`-'--`----enter-|  ,----. */
-             ,    ,    ,    ,    ,    ,    ,MUTE,    ,    ,    ,             ,   MUTE,
- /*|shift----`-z--`-x--`-c--`-v--`-b--`-n--`-m--`-,--`-.--`-/--`-------shift-.--|-up-|----. */
-         ,     ,     ,                              ,      ,     ,     ,    MPRV,MPLY,MNXT
- /*`ctrl-+-gui-+-alt-+----------space---------------+-fn---+-alt-+ctrl-'   `left+down+rght' */
+  [_FN1] = LAYOUT_68_ansi(
+    KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_BSPC,          KC_VOLU, KC_HOME,
+    _______, _______, _______, KC_UP,   _______, _______, _______, _______, _______, _______, _______, _______, BL_STEP, _______,          KC_VOLD, KC_END,
+    _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, _______, _______, _______, _______, _______,          _______,
+    _______, _______, _______, _______, _______, _______, _______, KC_MUTE, _______, _______, _______,                   _______,          KC_MUTE,
+    _______, _______, _______,                            _______,                            _______, _______, _______,          KC_MPRV, KC_MPLY, KC_MNXT
   ),
-
-  [_FN2] = LAYOUT_kc(
- /*,----+----+----+----+----+----+----+----+----+----+----+----+----+--------.  ,----+----. */
-    GRV , F1 , F2 , F3 , F4 , F5 , F6 , F7 , F8 , F9 ,F10 ,F11 ,F12 ,   BSPC ,   VOLU,HOME,
- /*|esc-`-1--`-2--`-3--`-4--`-5--`-6--`-7--`-8--`-9--`-0--`mnus`plus`--bksp--|  |ins-`pgup| */
-          ,    ,    , UP ,    ,    ,    , 7  , 8  , 9  ,    ,    ,    ,      ,   VOLD,END,
- /*|tab---`-q--`-w--`-e--`-r--`-t--`-y--`-u--`-i--`-o--`-p--`-{--`-}--`--|---|  `del-`pgdn' */
-           ,    ,LEFT,DOWN,RGHT,    ,    , 4  , 5  , 6  ,    ,    ,          ,
- /*|caps---`-a--`-s--`-d--`-f--`-g--`-h--`-j--`-k--`-l--`-;--`-'--`----enter-|  ,----. */
-             ,    ,    ,    ,    ,    , 0  , 1  , 2  , 3  ,    ,             ,   MUTE,
- /*|shift----`-z--`-x--`-c--`-v--`-b--`-n--`-m--`-,--`-.--`-/--`-------shift-.--|-up-|----. */
-         ,     ,     ,                              ,      ,     ,     ,    MPRV,MPLY,MNXT
- /*`ctrl-+-gui-+-alt-+----------space---------------+-fn---+-alt-+ctrl-'   `left+down+rght' */
+  [_FN2] = LAYOUT_68_ansi(
+    KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_BSPC,          KC_VOLU, KC_HOME,
+    _______, _______, _______, KC_UP,   _______, _______, _______, KC_7,    KC_8,    KC_9,    _______, _______, _______, _______,          KC_VOLD, KC_END,
+    _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, KC_4,    KC_5,    KC_6,    _______, _______,          _______,
+    _______, _______, _______, _______, _______, _______, KC_0,    KC_1,    KC_2,    KC_3,    _______,                   _______,          KC_MUTE,
+    _______, _______, _______,                            _______,                            _______, _______, _______,          KC_MPRV, KC_MPLY, KC_MNXT
   )
 };

keyboards/40percentclub/ut47/keymaps/default/config.h

@@ -16,6 +16,4 @@
 
 #pragma once
 
-#include "config_common.h"
-
 // place overrides here

keyboards/alice/alice.h

@@ -1,5 +1,5 @@
 /*
-Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+Copyright 2019 Felipe Coury <felipe.coury@gmail.com>
 
 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
@@ -21,30 +21,30 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 /* LAYOUT
  * ┌───┐ ┌───┬───┬───┬───┬───┬───┬───┐         ┌───┬───┬───┬───┬───┬───┬───┬───┐
- * │63 │ │00 │01 │02 │03 │04 │05 │06 │         │07 │08 │09 │10 │11 │12 │13 │14 │
+ * │50 │ │00 │01 │02 │03 │04 │05 │06 │         │07 │08 │09 │0A │0B │0C │0D │0E │
  * ├───┤ ├───┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┘       ┌─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴───┤
- * │64 │ │15   │16 │17 │18 │19 │20 │         │21 │22 │23 │24 │25 │26 │27 │28   │
+ * │51 │ │10   │11 │12 │13 │14 │15 │         │16 │17 │18 │19 │1A │1B │1C │1D   │
  * ├───┤ ├─────┴┬──┴┬──┴┬──┴┬──┴┬──┴┐        └┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴─────┤
- * │65 │ │29    │30 │31 │32 │33 │34 │         │35 │36 │37 │38 │39 │40 │41      │
+ * │52 │ │20    │21 │22 │23 │24 │25 │         │26 │27 │28 │29 │2A │2B │2C      │
  * └───┘ ├──────┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┐     ┌─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴────┬───┤
- *       │42      │43 │44 │45 │46 │47 │     │48 │49 │50 │51 │52 │53 │54    │55 │
+ *       │30      │31 │32 │33 │34 │35 │     │36 │37 │38 │39 │4A │4B │4C    │4D │
  *       ├─────┬──┴──┬┴───┴┬──┴───┴┬──┴─┐   ├───┴───┴──┬┴───┴┬──┴───┴────┬─┴───┤
- *       │56   │     │57   │58     │59  │   │60        │61   │           │62   │
+ *       │40   │     │41   │42     │43  │   │46        │47   │           │48   │
  *       └─────┘     └─────┴───────┴────┘   └──────────┴─────┘           └─────┘
  */
 #define LAYOUT( \
-  K63,   K00, K01, K02, K03, K04, K05, K06,      K07, K08, K09, K10, K11, K12, K13, K14, \
-  K64,   K15, K16, K17, K18, K19, K20,      K21, K22, K23, K24, K25, K26, K27, K28,      \
-  K65,   K29, K30, K31, K32, K33, K34,      K35, K36, K37, K38, K39, K40,      K41,      \
-         K42, K43, K44, K45, K46, K47,      K48, K49, K50, K51, K52, K53, K54, K55,      \
-         K56,      K57,      K58, K59,           K60,      K61,                K62       \
+  K50,   K00, K01, K02, K03, K04, K05, K06,      K07, K08, K09, K0A, K0B, K0C, K0D, K0E, \
+  K51,   K10, K11, K12, K13, K14, K15,      K16, K17, K18, K19, K1A, K1B, K1C, K1D,      \
+  K52,   K20, K21, K22, K23, K24, K25,      K26, K27, K28, K29, K2A, K2B,      K2C,      \
+         K30, K31, K32, K33, K34, K35,      K36, K37, K38, K39, K4A, K4B, K4C, K4D,      \
+         K40,      K41,      K42, K43,           K46,      K47,                K48       \
 ) \
 { \
-  { K00  , K01  , K02  , K03  , K04  , K05  , K06  , K07  , K08  , K09  , K10  , K11  , K12  , K13  , K14   }, \
-  { K15  , K16  , K17  , K18  , K19  , K20  , K21  , K22  , K23  , K24  , K25  , K26  , K27  , K28  , KC_NO }, \
-  { K29  , K30  , K31  , K32  , K33  , K34  , K35  , K36  , K37  , K38  , K39  , K40  , K41  , KC_NO, KC_NO }, \
-  { K42  , K43  , K44  , K45  , K46  , K47  , K48  , K49  , K50  , K51  , K52  , K53  , K54  , K55  , KC_NO }, \
-  { K56  , K57  , K58  , K59  , KC_NO, KC_NO, K60  , K61  , K62  , KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \
-  { K63  , K64  , K65  , KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }  \
+  { K00  , K01  , K02  , K03  , K04  , K05  , K06  , K07  , K08  , K09  , K0A  , K0B  , K0C  , K0D  , K0E   }, \
+  { K10  , K11  , K12  , K13  , K14  , K15  , K16  , K17  , K18  , K19  , K1A  , K1B  , K1C  , K1D  , KC_NO }, \
+  { K20  , K21  , K22  , K23  , K24  , K25  , K26  , K27  , K28  , K29  , K2A  , K2B  , K2C  , KC_NO, KC_NO }, \
+  { K30  , K31  , K32  , K33  , K34  , K35  , K36  , K37  , K38  , K39  , K4A  , K4B  , K4C  , K4D  , KC_NO }, \
+  { K40  , K41  , K42  , K43  , KC_NO, KC_NO, K46  , K47  , K48  , KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \
+  { K50  , K51  , K52  , KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }  \
 }
 

keyboards/amj96/keymaps/default/config.h

@@ -14,11 +14,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
 
-#include "config_common.h"
 
 // place overrides here
-
-#endif

keyboards/amjpad/keymaps/default/keymap.c

@@ -1,9 +1,5 @@
 #include QMK_KEYBOARD_H
 
-#ifdef RGBLIGHT_ENABLE
-#include "rgblight.h"
-#endif
-
 // Each layer gets a name for readability, which is then used in the keymap matrix below.
 // The underscores don't mean anything - you can have a layer called STUFF or any other name.
 // Layer names don't all need to be of the same length, obviously, and you can also skip them

keyboards/atomic/readme.md

@@ -3,7 +3,7 @@ Atomic
 
 ![Atomic](http://i.imgur.com/3gNDJAh.jpg)
 
-A compact 60% (15x5) ortholinear keyboard kit made and sold by OLKB. [More info on qmk.fm](http://qmk.fm/atomic/)
+A compact 60% (15x5) ortholinear keyboard kit made and sold by OLKB.
 
 Keyboard Maintainer: [Jack Humbert](https://github.com/jackhumbert)  
 Hardware Supported: Atomic PCB rev1, Teensy 2.0  

keyboards/bpiphany/tiger_lily/keymaps/default/config.h

@@ -1,8 +1,3 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
-
-#include "../../config.h"
+#pragma once
 
 // place overrides here
-
-#endif

keyboards/bpiphany/unloved_bastard/keymaps/default/config.h

@@ -14,11 +14,6 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
-
-#include "config_common.h"
+#pragma once
 
 // place overrides here
-
-#endif

keyboards/c39/c39.c

@@ -0,0 +1 @@
+#include "c39.h"

keyboards/c39/c39.h

@@ -0,0 +1,17 @@
+#pragma once
+
+#include "quantum.h"
+
+#define ___ KC_NO
+
+#define LAYOUT( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C  \
+  ) { \
+  { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C }, \
+  { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C }, \
+  { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C }  \
+}
+
+#define LAYOUT_ortho_3x13 LAYOUT

keyboards/c39/config.h

@@ -0,0 +1,89 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xCA17
+#define PRODUCT_ID      0xCA39
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Maple Computing
+#define PRODUCT         C39
+#define DESCRIPTION     A compact 39 key keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 3
+#define MATRIX_COLS 13
+
+#define MATRIX_ROW_PINS { D1, B4, B5 }
+#define MATRIX_COL_PINS { F4, F5, F6, F7, B1, B3, B2, B6, D7, E6, C6, D2, D3 }
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION

keyboards/c39/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "C39", 
+    "url": "", 
+    "maintainer": "Space Cat", 
+    "width": 13.25, 
+    "height": 3, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"label":"Q", "x":0, "y":0}, {"label":"W", "x":1, "y":0}, {"label":"E", "x":2, "y":0}, {"label":"R", "x":3, "y":0}, {"label":"T", "x":4, "y":0}, {"label":"Back", "x":5, "y":0}, {"label":"Y", "x":6, "y":0}, {"label":"U", "x":7, "y":0}, {"label":"I", "x":8, "y":0}, {"label":"O", "x":9, "y":0}, {"label":"P", "x":10, "y":0}, {"label":"M1", "x":11.25, "y":0}, {"label":"M2", "x":12.25, "y":0}, {"label":"A", "x":0, "y":1}, {"label":"S", "x":1, "y":1}, {"label":"D", "x":2, "y":1}, {"label":"F", "x":3, "y":1}, {"label":"G", "x":4, "y":1}, {"label":"Enter", "x":5, "y":1}, {"label":"H", "x":6, "y":1}, {"label":"J", "x":7, "y":1}, {"label":"K", "x":8, "y":1}, {"label":"L", "x":9, "y":1}, {"label":";", "x":10, "y":1}, {"label":"M3", "x":11.25, "y":1}, {"label":"M4", "x":12.25, "y":1}, {"label":"Z", "x":0, "y":2}, {"label":"X", "x":1, "y":2}, {"label":"C", "x":2, "y":2}, {"label":"V", "x":3, "y":2}, {"label":"B", "x":4, "y":2}, {"label":"Fn", "x":5, "y":2}, {"label":"N", "x":6, "y":2}, {"label":"M", "x":7, "y":2}, {"label":"<", "x":8, "y":2}, {"label":">", "x":9, "y":2}, {"label":"?", "x":10, "y":2}, {"label":"M5", "x":11.25, "y":2}, {"label":"M6", "x":12.25, "y":2}]
+        }
+    }
+}

keyboards/c39/keymaps/default/config.h

@@ -0,0 +1,3 @@
+#pragma once
+
+// place overrides here

keyboards/c39/keymaps/default/keymap.c

@@ -0,0 +1,45 @@
+#include QMK_KEYBOARD_H
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _QWERTY 0
+#define _FN1 1
+
+// Defines for task manager and such
+#define CALTDEL LCTL(LALT(KC_DEL))
+#define TSKMGR LCTL(LSFT(KC_ESC))
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+/* Qwerty
+ * ,----------------------------------------------------------------------------.  ,-------------.
+ * |   Q  |   W  |   E  |   R  |   T  | Bksp |   Y  |   U  |   I  |   O  |   P  |  |  M1  |  M2  |
+ * |------+------+------+------+------+------+------+------+------+------+------+  |------+------|
+ * |   A  |   S  |   D  |   F  |   G  | Enter|   H  |   J  |   K  |   L  |   ;  |  |  M3  |  M4  |
+ * |------+------+------+------+------+------+------+------+------+------+------+  |------+------|
+ * |   Z  |   X  |   C  |   V  |   B  |  FN1 |   N  |   M  |   ,  |   .  |   /  |  |  M5  |  M6  |
+ * `----------------------------------------------------------------------------'  `-------------'
+ */
+[_QWERTY] = LAYOUT(
+    KC_Q, KC_W, KC_E, KC_R, KC_T, KC_BSPC,                KC_Y, KC_U, KC_I,    KC_O,   KC_P,      KC_1, KC_2,
+    KC_A, KC_S, KC_D, KC_F, KC_G, MT(MOD_LSFT, KC_ENT),   KC_H, KC_J, KC_K,    KC_L,   KC_SCLN,   KC_3, KC_4,
+    KC_Z, KC_X, KC_C, KC_V, KC_B, LT(_FN1, KC_SPC),       KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH,   KC_5, KC_6
+),
+
+/* FN1
+ * ,----------------------------------------------------------------------------.  ,-------------.
+ * |   1  |   2  |   3  |   4  |   5  | Bksp |   6  |   7  |   8  |   9  |   0  |  |  M1  |  M2  |
+ * |------+------+------+------+------+------+------+------+------+------+------+  |------+------|
+ * |   4  |   5  |   6  |   +  |      | Enter|      |      |      |      |      |  |  M3  |  M4  |
+ * |------+------+------+------+------+------+------+------+------+------+------+  |------+------|
+ * |   7  |   8  |   9  |   0  |      |  FN1 |      |      |      |      |      |  |  M5  |  M6  |
+ * `----------------------------------------------------------------------------'  `-------------'
+ */
+[_FN1] = LAYOUT(
+    KC_1, KC_2, KC_3, KC_4,    KC_5,    KC_BSPC, KC_6,    KC_7,    KC_8,    KC_9,    KC_0,      KC_1, KC_2,
+    KC_4, KC_5, KC_6, KC_PLUS, _______, KC_ENT,  _______, _______, _______, _______, _______,   KC_3, KC_4,
+    KC_7, KC_8, KC_9, KC_0,    _______, _______, _______, _______, _______, _______, _______,   KC_5, KC_6
+),
+};

keyboards/c39/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for the C39

keyboards/c39/readme.md

@@ -0,0 +1,16 @@
+# C39
+=======
+
+![C39](https://i.imgur.com/KuWIIuW.png)
+
+A compact 39 key keyboard.
+
+Keyboard Maintainer: [Maple Computing]()  
+Hardware Supported: C39 PCB  
+Hardware Availability: [SpaceCat.design](https://spacecat.design)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make c39:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/c39/rules.mk

@@ -0,0 +1,66 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI controls
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+RGBLIGHT_ENABLE = no        # RGB Enable / Disable

keyboards/candybar/keymaps/default/keymap.c

@@ -14,7 +14,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-#include "candybar.h"
+#include QMK_KEYBOARD_H
 
 #define _BL 0
 #define _FL 1
@@ -35,4 +35,4 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   KC_TAB,KC_A,KC_SLCK,KC_D,KC_F,KC_G,KC_H,KC_J,KC_K,KC_L,KC_QUOT,KC_BSLS,KC_P4,KC_P5,KC_P6,KC_VOLD, \
   KC_LSFT,KC_Z,KC_X,KC_CAPS,KC_V,KC_B,KC_NLCK,KC_M,KC_COMM,KC_DOT,KC_SLSH,KC_PGUP,KC_P1,KC_P2,KC_P3,KC_PEQL, \
   KC_LCTL,KC_LGUI,KC_LALT,KC_SPC,KC_SPC,KC_BSPC,KC_APP,MO(_FL),KC_HOME,KC_PGDN,KC_END,KC_P0,KC_PDOT,KC_PENT),
-};
+};

keyboards/chibios_test/keymaps/default/keymap.c

@@ -15,7 +15,7 @@ You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
-#include "chibios_test.h"
+#include QMK_KEYBOARD_H
 
 const uint16_t keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     {{KC_CAPS}}, // test with KC_CAPS, KC_A, RESET

keyboards/christmas_tree/keymaps/default/config.h

@@ -1,6 +1,3 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
 
-#include "../../config.h"
-
-#endif
+// place overrides here

keyboards/ckeys/obelus/keymaps/default/config.h

@@ -1,6 +1,3 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
 
-#include "../../config.h"
-// Add overrides here 
-#endif
+// place overrides here

keyboards/ckeys/obelus/keymaps/default/keymap.c

@@ -1,7 +1,4 @@
 #include QMK_KEYBOARD_H
-#ifdef AUDIO_ENABLE
-  #include "audio.h"
-#endif
 
 extern keymap_config_t keymap_config;
 

keyboards/claw44/claw44.c

@@ -0,0 +1,10 @@
+#include "claw44.h"
+#include "ssd1306.h"
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+#ifdef SSD1306OLED
+  return process_record_gfx(keycode,record) && process_record_user(keycode, record);
+#else
+  return process_record_user(keycode, record);
+#endif
+}

keyboards/claw44/claw44.h

@@ -0,0 +1,5 @@
+#pragma once
+
+#ifdef KEYBOARD_claw44_rev1
+  #include "rev1.h"
+#endif

keyboards/claw44/config.h

@@ -0,0 +1,28 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+Copyright 2015 Jack Humbert
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+#include <serial_config.h>
+
+#define USE_I2C
+#define USE_SERIAL
+
+#define NO_ACTION_MACRO
+#define NO_ACTION_FUNCTION

keyboards/claw44/i2c.c

@@ -0,0 +1,162 @@
+#include <util/twi.h>
+#include <avr/io.h>
+#include <stdlib.h>
+#include <avr/interrupt.h>
+#include <util/twi.h>
+#include <stdbool.h>
+#include "i2c.h"
+
+#ifdef USE_I2C
+
+// Limits the amount of we wait for any one i2c transaction.
+// Since were running SCL line 100kHz (=> 10μs/bit), and each transactions is
+// 9 bits, a single transaction will take around 90μs to complete.
+//
+// (F_CPU/SCL_CLOCK)  =>  # of μC cycles to transfer a bit
+// poll loop takes at least 8 clock cycles to execute
+#define I2C_LOOP_TIMEOUT (9+1)*(F_CPU/SCL_CLOCK)/8
+
+#define BUFFER_POS_INC() (slave_buffer_pos = (slave_buffer_pos+1)%SLAVE_BUFFER_SIZE)
+
+volatile uint8_t i2c_slave_buffer[SLAVE_BUFFER_SIZE];
+
+static volatile uint8_t slave_buffer_pos;
+static volatile bool slave_has_register_set = false;
+
+// Wait for an i2c operation to finish
+inline static
+void i2c_delay(void) {
+  uint16_t lim = 0;
+  while(!(TWCR & (1<<TWINT)) && lim < I2C_LOOP_TIMEOUT)
+    lim++;
+
+  // easier way, but will wait slightly longer
+  // _delay_us(100);
+}
+
+// Setup twi to run at 100kHz or 400kHz (see ./i2c.h SCL_CLOCK)
+void i2c_master_init(void) {
+  // no prescaler
+  TWSR = 0;
+  // Set TWI clock frequency to SCL_CLOCK. Need TWBR>10.
+  // Check datasheets for more info.
+  TWBR = ((F_CPU/SCL_CLOCK)-16)/2;
+}
+
+// Start a transaction with the given i2c slave address. The direction of the
+// transfer is set with I2C_READ and I2C_WRITE.
+// returns: 0 => success
+//          1 => error
+uint8_t i2c_master_start(uint8_t address) {
+  TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTA);
+
+  i2c_delay();
+
+  // check that we started successfully
+  if ( (TW_STATUS != TW_START) && (TW_STATUS != TW_REP_START))
+    return 1;
+
+  TWDR = address;
+  TWCR = (1<<TWINT) | (1<<TWEN);
+
+  i2c_delay();
+
+  if ( (TW_STATUS != TW_MT_SLA_ACK) && (TW_STATUS != TW_MR_SLA_ACK) )
+    return 1; // slave did not acknowledge
+  else
+    return 0; // success
+}
+
+
+// Finish the i2c transaction.
+void i2c_master_stop(void) {
+  TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
+
+  uint16_t lim = 0;
+  while(!(TWCR & (1<<TWSTO)) && lim < I2C_LOOP_TIMEOUT)
+    lim++;
+}
+
+// Write one byte to the i2c slave.
+// returns 0 => slave ACK
+//         1 => slave NACK
+uint8_t i2c_master_write(uint8_t data) {
+  TWDR = data;
+  TWCR = (1<<TWINT) | (1<<TWEN);
+
+  i2c_delay();
+
+  // check if the slave acknowledged us
+  return (TW_STATUS == TW_MT_DATA_ACK) ? 0 : 1;
+}
+
+// Read one byte from the i2c slave. If ack=1 the slave is acknowledged,
+// if ack=0 the acknowledge bit is not set.
+// returns: byte read from i2c device
+uint8_t i2c_master_read(int ack) {
+  TWCR = (1<<TWINT) | (1<<TWEN) | (ack<<TWEA);
+
+  i2c_delay();
+  return TWDR;
+}
+
+void i2c_reset_state(void) {
+  TWCR = 0;
+}
+
+void i2c_slave_init(uint8_t address) {
+  TWAR = address << 0; // slave i2c address
+  // TWEN  - twi enable
+  // TWEA  - enable address acknowledgement
+  // TWINT - twi interrupt flag
+  // TWIE  - enable the twi interrupt
+  TWCR = (1<<TWIE) | (1<<TWEA) | (1<<TWINT) | (1<<TWEN);
+}
+
+ISR(TWI_vect);
+
+ISR(TWI_vect) {
+  uint8_t ack = 1;
+  switch(TW_STATUS) {
+    case TW_SR_SLA_ACK:
+      // this device has been addressed as a slave receiver
+      slave_has_register_set = false;
+      break;
+
+    case TW_SR_DATA_ACK:
+      // this device has received data as a slave receiver
+      // The first byte that we receive in this transaction sets the location
+      // of the read/write location of the slaves memory that it exposes over
+      // i2c.  After that, bytes will be written at slave_buffer_pos, incrementing
+      // slave_buffer_pos after each write.
+      if(!slave_has_register_set) {
+        slave_buffer_pos = TWDR;
+        // don't acknowledge the master if this memory loctaion is out of bounds
+        if ( slave_buffer_pos >= SLAVE_BUFFER_SIZE ) {
+          ack = 0;
+          slave_buffer_pos = 0;
+        }
+        slave_has_register_set = true;
+      } else {
+        i2c_slave_buffer[slave_buffer_pos] = TWDR;
+        BUFFER_POS_INC();
+      }
+      break;
+
+    case TW_ST_SLA_ACK:
+    case TW_ST_DATA_ACK:
+      // master has addressed this device as a slave transmitter and is
+      // requesting data.
+      TWDR = i2c_slave_buffer[slave_buffer_pos];
+      BUFFER_POS_INC();
+      break;
+
+    case TW_BUS_ERROR: // something went wrong, reset twi state
+      TWCR = 0;
+    default:
+      break;
+  }
+  // Reset everything, so we are ready for the next TWI interrupt
+  TWCR |= (1<<TWIE) | (1<<TWINT) | (ack<<TWEA) | (1<<TWEN);
+}
+#endif

keyboards/claw44/i2c.h

@@ -0,0 +1,46 @@
+#pragma once
+
+#include <stdint.h>
+
+#ifndef F_CPU
+#define F_CPU 16000000UL
+#endif
+
+#define I2C_READ 1
+#define I2C_WRITE 0
+
+#define I2C_ACK 1
+#define I2C_NACK 0
+
+#define SLAVE_BUFFER_SIZE 0x10
+
+// i2c SCL clock frequency 400kHz
+#define SCL_CLOCK  400000L
+
+extern volatile uint8_t i2c_slave_buffer[SLAVE_BUFFER_SIZE];
+
+void i2c_master_init(void);
+uint8_t i2c_master_start(uint8_t address);
+void i2c_master_stop(void);
+uint8_t i2c_master_write(uint8_t data);
+uint8_t i2c_master_read(int);
+void i2c_reset_state(void);
+void i2c_slave_init(uint8_t address);
+
+
+static inline unsigned char i2c_start_read(unsigned char addr) {
+  return i2c_master_start((addr << 1) | I2C_READ);
+}
+
+static inline unsigned char i2c_start_write(unsigned char addr) {
+  return i2c_master_start((addr << 1) | I2C_WRITE);
+}
+
+// from SSD1306 scrips
+extern unsigned char i2c_rep_start(unsigned char addr);
+extern void i2c_start_wait(unsigned char addr);
+extern unsigned char i2c_readAck(void);
+extern unsigned char i2c_readNak(void);
+extern unsigned char i2c_read(unsigned char ack);
+
+#define i2c_read(ack)  (ack) ? i2c_readAck() : i2c_readNak();

keyboards/claw44/keymaps/default/config.h

@@ -0,0 +1,35 @@
+/*
+This is the c configuration file for the keymap
+
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+Copyright 2015 Jack Humbert
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+//#define USE_MATRIX_I2C
+
+/* Select hand configuration */
+
+#define MASTER_LEFT
+// #define MASTER_RIGHT
+// #define EE_HANDS
+
+#define SSD1306OLED
+
+#define USE_SERIAL_PD2
+
+#define TAPPING_TERM 200

keyboards/claw44/keymaps/default/keymap.c

@@ -0,0 +1,169 @@
+#include QMK_KEYBOARD_H
+#ifdef PROTOCOL_LUFA
+  #include "lufa.h"
+  #include "split_util.h"
+#endif
+#ifdef SSD1306OLED
+  #include "ssd1306.h"
+#endif
+
+extern keymap_config_t keymap_config;
+
+extern uint8_t is_master;
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+
+enum custom_keycodes {
+  QWERTY = SAFE_RANGE,
+  LOWER,
+  RAISE
+};
+
+enum macro_keycodes {
+  KC_SAMPLEMACRO,
+};
+
+#define KC_ KC_TRNS
+#define KC_RST RESET
+#define KC_L_SPC LT(_LOWER, KC_SPC) // lower
+#define KC_R_ENT LT(_RAISE, KC_ENT) // raise
+#define KC_G_JA LGUI_T(KC_LANG1) // cmd or win
+#define KC_G_EN LGUI_T(KC_LANG2) // cmd or win
+#define KC_C_BS LCTL_T(KC_BSPC) // ctrl
+#define KC_A_DEL ALT_T(KC_DEL) // alt
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+  [_QWERTY] = LAYOUT( \
+  //,--------+--------+---------+--------+---------+--------.   ,--------+---------+--------+---------+--------+--------.
+     KC_ESC , KC_Q   , KC_W    , KC_E   , KC_R    , KC_T   ,     KC_Y   , KC_U    , KC_I   , KC_O    , KC_P   , KC_MINS,
+  //|--------+--------+---------+--------+---------+--------|   |--------+---------+--------+---------+--------+--------|
+     KC_TAB , KC_A   , KC_S    , KC_D   , KC_F    , KC_G   ,     KC_H   , KC_J    , KC_K   , KC_L    , KC_SCLN, KC_QUOT,
+  //|--------+--------+---------+--------+---------+--------|   |--------+---------+--------+---------+--------+--------|
+     KC_LSFT, KC_Z   , KC_X    , KC_C   , KC_V    , KC_B   ,     KC_N   , KC_M    , KC_COMM, KC_DOT  , KC_SLSH, KC_RSFT,
+  //`--------+--------+---------+--------+---------+--------/   \--------+---------+--------+---------+--------+--------'
+                       KC_A_DEL, KC_G_EN, KC_L_SPC, KC_C_BS,     KC_C_BS, KC_R_ENT, KC_G_JA, KC_A_DEL
+  //                 `----------+--------+---------+--------'   `--------+---------+--------+---------'
+  ),
+
+  //   \ ^ ! & |  @ = + * % -
+  // ( # $ " ' ~  ← ↓ ↑ → ` )
+  //         { [  ] }
+
+  [_RAISE] = LAYOUT( \
+  //,--------+--------+--------+--------+--------+--------.   ,--------+--------+--------+--------+--------+--------.
+     _______, KC_BSLS, KC_CIRC, KC_EXLM, KC_AMPR, KC_PIPE,     KC_AT  , KC_EQL , KC_PLUS, KC_ASTR, KC_PERC, KC_MINS,
+  //|--------+--------+--------+--------+--------+--------|   |--------+--------+--------+--------+--------+--------|
+     KC_LPRN, KC_HASH, KC_DLR , KC_DQT , KC_QUOT, KC_TILD,     KC_LEFT, KC_DOWN,  KC_UP , KC_RGHT, KC_GRV , KC_RPRN,
+  //|--------+--------+--------+--------+--------+--------|   |--------+--------+--------+--------+--------+--------|
+     _______, _______, _______, _______, KC_LCBR, KC_LBRC,     KC_RBRC, KC_RCBR, _______, _______, _______, _______,
+  //`--------+--------+--------+--------+--------+--------/   \--------+--------+--------+--------+--------+--------'
+                       _______, _______, _______, _______,     _______, _______, _______, RESET
+  //                  `--------+--------+--------+--------'   `--------+--------+--------+--------'
+  ),
+
+  [_LOWER] = LAYOUT( \
+  //,--------+--------+--------+--------+--------+--------.   ,--------+--------+--------+--------+--------+--------.
+     KC_F1  , KC_F2  , KC_F3  , KC_F4  , KC_F5  , KC_F6  ,     _______, KC_EQL , KC_PLUS, KC_ASTR, KC_PERC, KC_MINS,
+  //|--------+--------+--------+--------+--------+--------|   |--------+--------+--------+--------+--------+--------|
+     _______, KC_1   , KC_2   , KC_3   , KC_4   , KC_5   ,     KC_6   , KC_7   , KC_8   , KC_9   , KC_0   , _______,
+  //|--------+--------+--------+--------+--------+--------|   |--------+--------+--------+--------+--------+--------|
+     KC_F7  , KC_F8  , KC_F9  , KC_F10 , KC_F11 , KC_F12 ,     _______, _______, KC_COMM, KC_DOT , KC_SLSH, _______,
+  //`--------+--------+--------+--------+--------+--------/   \--------+--------+--------+--------+--------+--------'
+                       RESET  , _______, _______, _______,     _______, _______, _______, _______
+  //                  `--------+--------+--------+--------'   `--------+--------+--------+--------'
+  ),
+};
+
+void matrix_init_user(void) {
+  //SSD1306 OLED init, make sure to add #define SSD1306OLED in config.h
+  #ifdef SSD1306OLED
+    iota_gfx_init(!has_usb());   // turns on the display
+  #endif
+}
+
+//SSD1306 OLED update loop, make sure to add #define SSD1306OLED in config.h
+#ifdef SSD1306OLED
+
+// When add source files to SRC in rules.mk, you can use functions.
+const char *read_layer_state(void);
+const char *read_logo(void);
+void set_keylog(uint16_t keycode, keyrecord_t *record);
+const char *read_keylog(void);
+const char *read_keylogs(void);
+
+// const char *read_mode_icon(bool swap);
+// const char *read_host_led_state(void);
+// void set_timelog(void);
+// const char *read_timelog(void);
+
+void matrix_scan_user(void) {
+  iota_gfx_task();
+}
+
+void matrix_render_user(struct CharacterMatrix *matrix) {
+  if (is_master) {
+    // If you want to change the display of OLED, you need to change here
+    matrix_write_ln(matrix, read_layer_state());
+    matrix_write_ln(matrix, read_keylog());
+    matrix_write_ln(matrix, read_keylogs());
+    //matrix_write_ln(matrix, read_mode_icon(keymap_config.swap_lalt_lgui));
+    //matrix_write_ln(matrix, read_host_led_state());
+    //matrix_write_ln(matrix, read_timelog());
+  } else {
+    matrix_write(matrix, read_logo());
+  }
+}
+
+void matrix_update(struct CharacterMatrix *dest, const struct CharacterMatrix *source) {
+  if (memcmp(dest->display, source->display, sizeof(dest->display))) {
+    memcpy(dest->display, source->display, sizeof(dest->display));
+    dest->dirty = true;
+  }
+}
+
+void iota_gfx_task_user(void) {
+  struct CharacterMatrix matrix;
+  matrix_clear(&matrix);
+  matrix_render_user(&matrix);
+  matrix_update(&display, &matrix);
+}
+#endif//SSD1306OLED
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  if (record->event.pressed) {
+#ifdef SSD1306OLED
+    set_keylog(keycode, record);
+#endif
+    // set_timelog();
+  }
+
+  switch (keycode) {
+    case QWERTY:
+      if (record->event.pressed) {
+        set_single_persistent_default_layer(_QWERTY);
+      }
+      return false;
+      break;
+    case LOWER:
+      if (record->event.pressed) {
+        layer_on(_LOWER);
+      } else {
+        layer_off(_LOWER);
+      }
+      return false;
+      break;
+    case RAISE:
+      if (record->event.pressed) {
+        layer_on(_RAISE);
+      } else {
+        layer_off(_RAISE);
+      }
+      return false;
+      break;
+  }
+  return true;
+}

keyboards/claw44/keymaps/yfuku/config.h

@@ -0,0 +1,36 @@
+/*
+This is the c configuration file for the keymap
+
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+Copyright 2015 Jack Humbert
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+//#define USE_MATRIX_I2C
+
+/* Select hand configuration */
+
+#define MASTER_LEFT
+// #define MASTER_RIGHT
+// #define EE_HANDS
+
+#define SSD1306OLED
+
+#define USE_SERIAL_PD2
+
+#define TAPPING_TERM 180
+#define IGNORE_MOD_TAP_INTERRUPT

keyboards/claw44/keymaps/yfuku/keymap.c

@@ -0,0 +1,221 @@
+#include QMK_KEYBOARD_H
+#ifdef PROTOCOL_LUFA
+  #include "lufa.h"
+  #include "split_util.h"
+#endif
+#ifdef SSD1306OLED
+  #include "ssd1306.h"
+#endif
+
+extern keymap_config_t keymap_config;
+
+extern uint8_t is_master;
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+enum custom_keycodes {
+  QWERTY = SAFE_RANGE,
+  LOWER,
+  RAISE
+};
+
+enum macro_keycodes {
+  KC_SAMPLEMACRO,
+};
+
+// common
+#define KC_ KC_TRNS
+#define KC_XXXX KC_NO
+#define KC_RST RESET
+#define KC_VD KC__VOLDOWN
+#define KC_VU KC__VOLUP
+
+// layer
+#define KC_L_SPC LT(_LOWER, KC_SPC)
+#define KC_R_ENT LT(_RAISE, KC_ENT)
+
+// shift_t
+#define KC_S_TAB LSFT_T(KC_TAB)
+#define KC_S_ESC LSFT_T(KC_ESC)
+#define KC_S_JA LSFT_T(KC_LANG1)
+#define KC_S_EN LSFT_T(KC_LANG2)
+
+// cmd_t
+#define KC_M_F LCMD_T(KC_F)
+#define KC_M_D LCMD_T(KC_D)
+#define KC_M_J LCMD_T(KC_J)
+#define KC_M_K LCMD_T(KC_K)
+
+// ctl_t
+#define KC_C_S LCTL_T(KC_S)
+#define KC_C_L LCTL_T(KC_L)
+#define KC_C_BS LCTL_T(KC_BSPC)
+
+// alt_t
+#define KC_A_D ALT_T(KC_D)
+#define KC_A_K ALT_T(KC_K)
+#define KC_A_Z ALT_T(KC_Z)
+#define KC_A_SL ALT_T(KC_SLSH)
+#define KC_A_DEL ALT_T(KC_DEL)
+
+// cmd+shift_t
+#define KC_MS_Q SCMD_T(KC_Q)
+#define KC_MS_A SCMD_T(KC_A)
+#define KC_MS_S SCMD_T(KC_S)
+#define KC_MS_SC SCMD_T(KC_SCLN)
+#define KC_MS_ESC SCMD_T(KC_ESC)
+
+//
+#define KC_MR RCMD(KC_R)
+#define KC_MF RCMD(KC_F)
+#define KC_MW RCMD(KC_W)
+#define KC_MX RCMD(KC_X)
+#define KC_MC RCMD(KC_C)
+#define KC_MV RCMD(KC_V)
+#define KC_MTAB RCMD(KC_TAB)
+#define KC_MSF RCMD(RSFT(KC_F))
+#define KC_MSR RCMD(RSFT(KC_R))
+#define KC_MST RCMD(RSFT(KC_T))
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+  // M_ = LCMD_T(
+  // A_ = ALT_T(
+  // C_ = LCTL_T(
+  // MS_ = SMD_T(
+  // R_ = LT(_RAISE
+  // L_ = LT(_LOWER
+
+  [_QWERTY] = LAYOUT_kc( \
+  //,----+----+----+----+----+----.     ,----+----+----+----+----+----.
+     ESC , Q  , W  , E  , R  , T  ,       Y  , U  , I  , O  , P  ,MINS,
+  //|----+----+----+----+----+----|     |----+----+----+----+----+----|
+    S_TAB, A  ,C_S , D  ,M_F , G  ,       H  ,M_J , K  ,C_L ,SCLN,S_ESC,
+  //|----+----+----+----+----+----+     |----+----+----+----+----+----|
+         , Z  , X  , C  , V  , B  ,       N  , M  ,COMM,DOT ,SLSH,    ,
+  //`----+----+----+----+----+----/     \----+----+----+----+----+----'
+             A_DEL,S_EN,L_SPC,C_BS,      C_BS,R_ENT,S_JA,A_DEL
+  //          `----+----+----+----'     `----+----+----+----'
+  ),
+
+  //   \ ^ ! & |  @ = + * % -
+  // ( # $ " ' ~  ← ↓ ↑ → ` )
+  //         { [  ] }
+
+  [_RAISE] = LAYOUT_kc( \
+  //,----+----+----+----+----+----.     ,----+----+----+----+----+----.
+         ,BSLS,CIRC,EXLM,AMPR,PIPE,      AT  ,EQL ,PLUS,ASTR,PERC,MINS,
+  //|----+----+----+----+----+----|     |----+----+----+----+----+----|
+     LPRN,HASH,DLR ,DQT ,QUOT,TILD,      LEFT,DOWN, UP ,RGHT,GRV ,RPRN,
+  //|----+----+----+----+----+----|     |----+----+----+----+----+----|
+        ,     ,    ,    ,LCBR,LBRC,      RBRC,RCBR,    ,    ,    ,    ,
+  //`----+----+----+----+----+----/     \----+----+----+----+----+----'
+                   ,    ,BSPC,    ,          ,    ,    ,RST
+  //          `----+----+----+----'     `----+----+----+----'
+  ),
+
+  [_LOWER] = LAYOUT_kc( \
+  //,----+----+----+----+----+----.     ,----+----+----+----+----+----.
+         ,    ,    ,MSF ,MSR ,MST ,          ,EQL ,PLUS,ASTR,PERC,MINS,
+  //|----+----+----+----+----+----|     |----+----+----+----+----+----|
+         , 1  , 2  , 3  , 4  , 5  ,       6  , 7  , 8  , 9  , 0  ,    ,
+  //|----+----+----+----+----+----|     |----+----+----+----+----+----|
+         ,    ,    ,    ,    ,    ,          ,    ,COMM,DOT ,SLSH,    ,
+  //`----+----+----+--+-+----+----/     \----+----+----+----+----+----'
+               RST ,    ,    ,    ,          ,DEL ,    ,
+  //          `----+----+----+----'     `----+----+----+----'
+  ),
+};
+
+void matrix_init_user(void) {
+  //SSD1306 OLED init, make sure to add #define SSD1306OLED in config.h
+  #ifdef SSD1306OLED
+    iota_gfx_init(!has_usb());   // turns on the display
+  #endif
+}
+
+//SSD1306 OLED update loop, make sure to add #define SSD1306OLED in config.h
+#ifdef SSD1306OLED
+
+// When add source files to SRC in rules.mk, you can use functions.
+const char *read_layer_state(void);
+const char *read_logo(void);
+void set_keylog(uint16_t keycode, keyrecord_t *record);
+const char *read_keylog(void);
+const char *read_keylogs(void);
+
+// const char *read_mode_icon(bool swap);
+// const char *read_host_led_state(void);
+// void set_timelog(void);
+// const char *read_timelog(void);
+
+void matrix_scan_user(void) {
+  iota_gfx_task();
+}
+
+void matrix_render_user(struct CharacterMatrix *matrix) {
+  if (is_master) {
+    // If you want to change the display of OLED, you need to change here
+    matrix_write_ln(matrix, read_layer_state());
+    matrix_write_ln(matrix, read_keylog());
+    matrix_write_ln(matrix, read_keylogs());
+    //matrix_write_ln(matrix, read_mode_icon(keymap_config.swap_lalt_lgui));
+    //matrix_write_ln(matrix, read_host_led_state());
+    //matrix_write_ln(matrix, read_timelog());
+  } else {
+    matrix_write(matrix, read_logo());
+  }
+}
+
+void matrix_update(struct CharacterMatrix *dest, const struct CharacterMatrix *source) {
+  if (memcmp(dest->display, source->display, sizeof(dest->display))) {
+    memcpy(dest->display, source->display, sizeof(dest->display));
+    dest->dirty = true;
+  }
+}
+
+void iota_gfx_task_user(void) {
+  struct CharacterMatrix matrix;
+  matrix_clear(&matrix);
+  matrix_render_user(&matrix);
+  matrix_update(&display, &matrix);
+}
+#endif//SSD1306OLED
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  if (record->event.pressed) {
+#ifdef SSD1306OLED
+    set_keylog(keycode, record);
+#endif
+    // set_timelog();
+  }
+
+  switch (keycode) {
+    case QWERTY:
+      if (record->event.pressed) {
+        set_single_persistent_default_layer(_QWERTY);
+      }
+      return false;
+      break;
+    case LOWER:
+      if (record->event.pressed) {
+        layer_on(_LOWER);
+      } else {
+        layer_off(_LOWER);
+      }
+      return false;
+      break;
+    case RAISE:
+      if (record->event.pressed) {
+        layer_on(_RAISE);
+      } else {
+        layer_off(_RAISE);
+      }
+      return false;
+      break;
+  }
+  return true;
+}
+

keyboards/claw44/lib/glcdfont.c

@@ -0,0 +1,243 @@
+// This is the 'classic' fixed-space bitmap font for Adafruit_GFX since 1.0.
+// See gfxfont.h for newer custom bitmap font info.
+
+#ifndef FONT5X7_H
+#define FONT5X7_H
+
+#ifdef __AVR__
+ #include <avr/io.h>
+ #include <avr/pgmspace.h>
+#elif defined(ESP8266)
+ #include <pgmspace.h>
+#else
+ #define PROGMEM
+#endif
+
+// Standard ASCII 5x7 font
+const unsigned char font[] PROGMEM = {
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x3E, 0x5B, 0x4F, 0x5B, 0x3E, 0x00,
+0x3E, 0x6B, 0x4F, 0x6B, 0x3E, 0x00,
+0x1C, 0x3E, 0x7C, 0x3E, 0x1C, 0x00,
+0x18, 0x3C, 0x7E, 0x3C, 0x18, 0x00,
+0x1C, 0x57, 0x7D, 0x57, 0x1C, 0x00,
+0x1C, 0x5E, 0x7F, 0x5E, 0x1C, 0x00,
+0x00, 0x18, 0x3C, 0x18, 0x00, 0x00,
+0xFF, 0xE7, 0xC3, 0xE7, 0xFF, 0x00,
+0x00, 0x18, 0x24, 0x18, 0x00, 0x00,
+0xFF, 0xE7, 0xDB, 0xE7, 0xFF, 0x00,
+0x30, 0x48, 0x3A, 0x06, 0x0E, 0x00,
+0x26, 0x29, 0x79, 0x29, 0x26, 0x00,
+0x40, 0x7F, 0x05, 0x05, 0x07, 0x00,
+0x40, 0x7F, 0x05, 0x25, 0x3F, 0x00,
+0x5A, 0x3C, 0xE7, 0x3C, 0x5A, 0x00,
+0x7F, 0x3E, 0x1C, 0x1C, 0x08, 0x00,
+0x08, 0x1C, 0x1C, 0x3E, 0x7F, 0x00,
+0x14, 0x22, 0x7F, 0x22, 0x14, 0x00,
+0x5F, 0x5F, 0x00, 0x5F, 0x5F, 0x00,
+0x06, 0x09, 0x7F, 0x01, 0x7F, 0x00,
+0x00, 0x66, 0x89, 0x95, 0x6A, 0x00,
+0x60, 0x60, 0x60, 0x60, 0x60, 0x00,
+0x94, 0xA2, 0xFF, 0xA2, 0x94, 0x00,
+0x08, 0x04, 0x7E, 0x04, 0x08, 0x00,
+0x10, 0x20, 0x7E, 0x20, 0x10, 0x00,
+0x08, 0x08, 0x2A, 0x1C, 0x08, 0x00,
+0x08, 0x1C, 0x2A, 0x08, 0x08, 0x00,
+0x1E, 0x10, 0x10, 0x10, 0x10, 0x00,
+0x0C, 0x1E, 0x0C, 0x1E, 0x0C, 0x00,
+0x30, 0x38, 0x3E, 0x38, 0x30, 0x00,
+0x06, 0x0E, 0x3E, 0x0E, 0x06, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x5F, 0x00, 0x00, 0x00,
+0x00, 0x07, 0x00, 0x07, 0x00, 0x00,
+0x14, 0x7F, 0x14, 0x7F, 0x14, 0x00,
+0x24, 0x2A, 0x7F, 0x2A, 0x12, 0x00,
+0x23, 0x13, 0x08, 0x64, 0x62, 0x00,
+0x36, 0x49, 0x56, 0x20, 0x50, 0x00,
+0x00, 0x08, 0x07, 0x03, 0x00, 0x00,
+0x00, 0x1C, 0x22, 0x41, 0x00, 0x00,
+0x00, 0x41, 0x22, 0x1C, 0x00, 0x00,
+0x2A, 0x1C, 0x7F, 0x1C, 0x2A, 0x00,
+0x08, 0x08, 0x3E, 0x08, 0x08, 0x00,
+0x00, 0x80, 0x70, 0x30, 0x00, 0x00,
+0x08, 0x08, 0x08, 0x08, 0x08, 0x00,
+0x00, 0x00, 0x60, 0x60, 0x00, 0x00,
+0x20, 0x10, 0x08, 0x04, 0x02, 0x00,
+0x3E, 0x51, 0x49, 0x45, 0x3E, 0x00,
+0x00, 0x42, 0x7F, 0x40, 0x00, 0x00,
+0x72, 0x49, 0x49, 0x49, 0x46, 0x00,
+0x21, 0x41, 0x49, 0x4D, 0x33, 0x00,
+0x18, 0x14, 0x12, 0x7F, 0x10, 0x00,
+0x27, 0x45, 0x45, 0x45, 0x39, 0x00,
+0x3C, 0x4A, 0x49, 0x49, 0x31, 0x00,
+0x41, 0x21, 0x11, 0x09, 0x07, 0x00,
+0x36, 0x49, 0x49, 0x49, 0x36, 0x00,
+0x46, 0x49, 0x49, 0x29, 0x1E, 0x00,
+0x00, 0x00, 0x14, 0x00, 0x00, 0x00,
+0x00, 0x40, 0x34, 0x00, 0x00, 0x00,
+0x00, 0x08, 0x14, 0x22, 0x41, 0x00,
+0x14, 0x14, 0x14, 0x14, 0x14, 0x00,
+0x00, 0x41, 0x22, 0x14, 0x08, 0x00,
+0x02, 0x01, 0x59, 0x09, 0x06, 0x00,
+0x3E, 0x41, 0x5D, 0x59, 0x4E, 0x00,
+0x7C, 0x12, 0x11, 0x12, 0x7C, 0x00,
+0x7F, 0x49, 0x49, 0x49, 0x36, 0x00,
+0x3E, 0x41, 0x41, 0x41, 0x22, 0x00,
+0x7F, 0x41, 0x41, 0x41, 0x3E, 0x00,
+0x7F, 0x49, 0x49, 0x49, 0x41, 0x00,
+0x7F, 0x09, 0x09, 0x09, 0x01, 0x00,
+0x3E, 0x41, 0x41, 0x51, 0x73, 0x00,
+0x7F, 0x08, 0x08, 0x08, 0x7F, 0x00,
+0x00, 0x41, 0x7F, 0x41, 0x00, 0x00,
+0x20, 0x40, 0x41, 0x3F, 0x01, 0x00,
+0x7F, 0x08, 0x14, 0x22, 0x41, 0x00,
+0x7F, 0x40, 0x40, 0x40, 0x40, 0x00,
+0x7F, 0x02, 0x1C, 0x02, 0x7F, 0x00,
+0x7F, 0x04, 0x08, 0x10, 0x7F, 0x00,
+0x3E, 0x41, 0x41, 0x41, 0x3E, 0x00,
+0x7F, 0x09, 0x09, 0x09, 0x06, 0x00,
+0x3E, 0x41, 0x51, 0x21, 0x5E, 0x00,
+0x7F, 0x09, 0x19, 0x29, 0x46, 0x00,
+0x26, 0x49, 0x49, 0x49, 0x32, 0x00,
+0x03, 0x01, 0x7F, 0x01, 0x03, 0x00,
+0x3F, 0x40, 0x40, 0x40, 0x3F, 0x00,
+0x1F, 0x20, 0x40, 0x20, 0x1F, 0x00,
+0x3F, 0x40, 0x38, 0x40, 0x3F, 0x00,
+0x63, 0x14, 0x08, 0x14, 0x63, 0x00,
+0x03, 0x04, 0x78, 0x04, 0x03, 0x00,
+0x61, 0x59, 0x49, 0x4D, 0x43, 0x00,
+0x00, 0x7F, 0x41, 0x41, 0x41, 0x00,
+0x02, 0x04, 0x08, 0x10, 0x20, 0x00,
+0x00, 0x41, 0x41, 0x41, 0x7F, 0x00,
+0x04, 0x02, 0x01, 0x02, 0x04, 0x00,
+0x40, 0x40, 0x40, 0x40, 0x40, 0x00,
+0x00, 0x03, 0x07, 0x08, 0x00, 0x00,
+0x20, 0x54, 0x54, 0x78, 0x40, 0x00,
+0x7F, 0x28, 0x44, 0x44, 0x38, 0x00,
+0x38, 0x44, 0x44, 0x44, 0x28, 0x00,
+0x38, 0x44, 0x44, 0x28, 0x7F, 0x00,
+0x38, 0x54, 0x54, 0x54, 0x18, 0x00,
+0x00, 0x08, 0x7E, 0x09, 0x02, 0x00,
+0x18, 0x24, 0x24, 0x1C, 0x78, 0x00,
+0x7F, 0x08, 0x04, 0x04, 0x78, 0x00,
+0x00, 0x44, 0x7D, 0x40, 0x00, 0x00,
+0x20, 0x40, 0x40, 0x3D, 0x00, 0x00,
+0x7F, 0x10, 0x28, 0x44, 0x00, 0x00,
+0x00, 0x41, 0x7F, 0x40, 0x00, 0x00,
+0x7C, 0x04, 0x78, 0x04, 0x78, 0x00,
+0x7C, 0x08, 0x04, 0x04, 0x78, 0x00,
+0x38, 0x44, 0x44, 0x44, 0x38, 0x00,
+0x7C, 0x18, 0x24, 0x24, 0x18, 0x00,
+0x18, 0x24, 0x24, 0x18, 0x7C, 0x00,
+0x7C, 0x08, 0x04, 0x04, 0x08, 0x00,
+0x48, 0x54, 0x54, 0x54, 0x24, 0x00,
+0x04, 0x04, 0x3F, 0x44, 0x24, 0x00,
+0x3C, 0x40, 0x40, 0x20, 0x7C, 0x00,
+0x1C, 0x20, 0x40, 0x20, 0x1C, 0x00,
+0x3C, 0x40, 0x30, 0x40, 0x3C, 0x00,
+0x44, 0x28, 0x10, 0x28, 0x44, 0x00,
+0x4C, 0x90, 0x90, 0x90, 0x7C, 0x00,
+0x44, 0x64, 0x54, 0x4C, 0x44, 0x00,
+0x00, 0x08, 0x36, 0x41, 0x00, 0x00,
+0x00, 0x00, 0x77, 0x00, 0x00, 0x00,
+0x00, 0x41, 0x36, 0x08, 0x00, 0x00,
+0x02, 0x01, 0x02, 0x04, 0x02, 0x00,
+0x3C, 0x26, 0x23, 0x26, 0x3C, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x80, 0x80, 0x80, 0x80, 0x80,
+  0x80, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0xFC, 0xFC, 0xFC, 0xFC, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x80, 0x80, 0x80, 0x80, 0x80, 0x80,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x80,
+  0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+  0x00, 0x80, 0x80, 0x80, 0x80, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x80, 0x80,
+  0x80, 0x80, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x80, 0xC0, 0xF0, 0xF8, 0xF8,
+  0xF8, 0xF8, 0xF8, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x80,
+  0xE0, 0xF8, 0xF8, 0xF8, 0xF8, 0xF8,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0xE0, 0xF0, 0xF0, 0xF0, 0xE0, 0xEC,
+0xEE, 0xF7, 0xF3, 0x70, 0x20, 0x00,
+0x7C, 0x7C, 0x7C, 0x7E, 0x00, 0x7E,
+0x7E, 0x7E, 0x7F, 0x7F, 0x7F, 0x00,
+0x00, 0x80, 0xC0, 0xE0, 0x7E, 0x5B,
+0x4F, 0x5B, 0xFE, 0xC0, 0x00, 0x00,
+0xC0, 0x00, 0xDC, 0xD7, 0xDE, 0xDE,
+0xDE, 0xD7, 0xDC, 0x00, 0xC0, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0xF8, 0xFC, 0xFE,
+  0xFF, 0x1F, 0x07, 0x07, 0x07, 0x07,
+  0x1F, 0x1F, 0x1F, 0x1E, 0x18, 0x00,
+  0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0x00,
+  0x00, 0x00, 0x00, 0x9E, 0xDF, 0xDF,
+  0xCF, 0xC7, 0xE7, 0xE7, 0xE7, 0xFF,
+  0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x03,
+  0x3F, 0xFF, 0xFF, 0xFE, 0xC0, 0x00,
+  0xF0, 0xFF, 0xFF, 0x1F, 0xFF, 0xFF,
+  0xF0, 0x00, 0xC0, 0xFC, 0xFF, 0xFF,
+  0x3F, 0x03, 0x00, 0xC0, 0xF0, 0xF8,
+  0xFE, 0x9F, 0x87, 0x83, 0x80, 0xFF,
+  0xFF, 0xFF, 0xFF, 0x80, 0x80, 0x00,
+  0x00, 0xE0, 0xF8, 0xFC, 0xBF, 0x8F,
+  0x83, 0x81, 0xFF, 0xFF, 0xFF, 0xFF,
+  0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x0F, 0x1F, 0x3F, 0x7F, 0x7F, 0x7F,
+0x7F, 0x7F, 0x3F, 0x1E, 0x0C, 0x00,
+0x1F, 0x1F, 0x1F, 0x3F, 0x00, 0x3F,
+0x3F, 0x3F, 0x7F, 0x7F, 0x7F, 0x00,
+0x30, 0x7B, 0x7F, 0x78, 0x30, 0x20,
+0x20, 0x30, 0x78, 0x7F, 0x3B, 0x00,
+0x03, 0x00, 0x0F, 0x7F, 0x0F, 0x0F,
+0x0F, 0x7F, 0x0F, 0x00, 0x03, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x07, 0x1F, 0x3F,
+  0x7F, 0x7C, 0x78, 0x70, 0x70, 0x78,
+  0x7E, 0x3E, 0x3E, 0x0E, 0x06, 0x00,
+  0x00, 0x7F, 0x7F, 0x7F, 0x7F, 0x00,
+  0x00, 0x00, 0x1F, 0x3F, 0x7F, 0x7F,
+  0x79, 0x71, 0x70, 0x30, 0x38, 0x3F,
+  0x7F, 0x7F, 0x7F, 0x60, 0x00, 0x00,
+  0x00, 0x01, 0x1F, 0x7F, 0x7F, 0x7E,
+  0x7F, 0x1F, 0x01, 0x00, 0x01, 0x3F,
+  0x7F, 0x7E, 0x7F, 0x7F, 0x0F, 0x01,
+  0x00, 0x00, 0x00, 0x03, 0x03, 0x03,
+  0x03, 0x03, 0x03, 0x03, 0x03, 0x7F,
+  0x7F, 0x7F, 0x7F, 0x03, 0x03, 0x00,
+  0x00, 0x03, 0x03, 0x03, 0x03, 0x03,
+  0x03, 0x03, 0x7F, 0x7F, 0x7F, 0x7F,
+  0x07, 0x03, 0x03, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+  0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+};
+#endif // FONT5X7_H

keyboards/claw44/lib/host_led_state_reader.c

@@ -0,0 +1,15 @@
+#include <stdio.h>
+#include "claw44.h"
+
+char host_led_state_str[24];
+
+const char *read_host_led_state(void)
+{
+  uint8_t leds = host_keyboard_leds();
+  snprintf(host_led_state_str, sizeof(host_led_state_str), "NL:%s CL:%s SL:%s",
+           (leds & (1 << USB_LED_NUM_LOCK)) ? "on" : "- ",
+           (leds & (1 << USB_LED_CAPS_LOCK)) ? "on" : "- ",
+           (leds & (1 << USB_LED_SCROLL_LOCK)) ? "on" : "- ");
+
+  return host_led_state_str;
+}

keyboards/claw44/lib/keylogger.c

@@ -0,0 +1,45 @@
+#include <stdio.h>
+#include "claw44.h"
+
+char keylog_str[24] = {};
+char keylogs_str[21] = {};
+int keylogs_str_idx = 0;
+
+const char code_to_name[60] = {
+    ' ', ' ', ' ', ' ', 'a', 'b', 'c', 'd', 'e', 'f',
+    'g', 'h', 'i', 'j', 'k', 'l', 'm', 'n', 'o', 'p',
+    'q', 'r', 's', 't', 'u', 'v', 'w', 'x', 'y', 'z',
+    '1', '2', '3', '4', '5', '6', '7', '8', '9', '0',
+    'R', 'E', 'B', 'T', ' ', ' ', ' ', ' ', ' ', ' ',
+    ' ', ';', '\'', ' ', ',', '.', '/', ' ', ' ', ' '};
+
+void set_keylog(uint16_t keycode, keyrecord_t *record) {
+  char name = ' ';
+  if (keycode < 60) {
+    name = code_to_name[keycode];
+  }
+
+  // update keylog
+  snprintf(keylog_str, sizeof(keylog_str), "%dx%d, k%2d : %c",
+           record->event.key.row, record->event.key.col,
+           keycode, name);
+
+  // update keylogs
+  if (keylogs_str_idx == sizeof(keylogs_str) - 1) {
+    keylogs_str_idx = 0;
+    for (int i = 0; i < sizeof(keylogs_str) - 1; i++) {
+      keylogs_str[i] = ' ';
+    }
+  }
+
+  keylogs_str[keylogs_str_idx] = name;
+  keylogs_str_idx++;
+}
+
+const char *read_keylog(void) {
+  return keylog_str;
+}
+
+const char *read_keylogs(void) {
+  return keylogs_str;
+}

keyboards/claw44/lib/layer_state_reader.c

@@ -0,0 +1,35 @@
+
+#include QMK_KEYBOARD_H
+#include <stdio.h>
+#include "claw44.h"
+
+#define L_BASE 0
+#define L_LOWER (1<<_LOWER)
+#define L_RAISE (1<<_RAISE)
+#define L_ADJUST (1<<_ADJUST)
+#define L_ADJUST_TRI (L_ADJUST|L_RAISE|L_LOWER)
+
+char layer_state_str[24];
+
+const char *read_layer_state(void) {
+  switch (layer_state)
+  {
+  case L_BASE:
+    snprintf(layer_state_str, sizeof(layer_state_str), "Layer: Default");
+    break;
+  case L_RAISE:
+    snprintf(layer_state_str, sizeof(layer_state_str), "Layer: Raise");
+    break;
+  case L_LOWER:
+    snprintf(layer_state_str, sizeof(layer_state_str), "Layer: Lower");
+    break;
+  case L_ADJUST:
+  case L_ADJUST_TRI:
+    snprintf(layer_state_str, sizeof(layer_state_str), "Layer: Adjust");
+    break;
+  default:
+    snprintf(layer_state_str, sizeof(layer_state_str), "Layer: Undef-%ld", layer_state);
+  }
+
+  return layer_state_str;
+}

keyboards/claw44/lib/logo_reader.c

@@ -0,0 +1,11 @@
+#include "claw44.h"
+
+const char *read_logo(void) {
+  static char logo[] = {
+      0x80, 0x81, 0x82, 0x83, 0x84, 0x85, 0x86, 0x87, 0x88, 0x89, 0x8a, 0x8b, 0x8c, 0x8d, 0x8e, 0x8f, 0x90, 0x91, 0x92, 0x93, 0x94,
+      0xa0, 0xa1, 0xa2, 0xa3, 0xa4, 0xa5, 0xa6, 0xa7, 0xa8, 0xa9, 0xaa, 0xab, 0xac, 0xad, 0xae, 0xaf, 0xb0, 0xb1, 0xb2, 0xb3, 0xb4,
+      0xc0, 0xc1, 0xc2, 0xc3, 0xc4, 0xc5, 0xc6, 0xc7, 0xc8, 0xc9, 0xca, 0xcb, 0xcc, 0xcd, 0xce, 0xcf, 0xd0, 0xd1, 0xd2, 0xd3, 0xd4,
+      0};
+
+  return logo;
+}

keyboards/claw44/lib/mode_icon_reader.c

@@ -0,0 +1,15 @@
+#include <stdio.h>
+#include "claw44.h"
+
+char mode_icon[24];
+
+const char *read_mode_icon(bool swap) {
+  static char logo[][2][3] = {{{0x95, 0x96, 0}, {0xb5, 0xb6, 0}}, {{0x97, 0x98, 0}, {0xb7, 0xb8, 0}}};
+  if (swap == false) {
+    snprintf(mode_icon, sizeof(mode_icon), "%s\n%s", logo[0][0], logo[0][1]);
+  } else {
+    snprintf(mode_icon, sizeof(mode_icon), "%s\n%s", logo[1][0], logo[1][1]);
+  }
+
+  return mode_icon;
+}

keyboards/claw44/lib/rgb_state_reader.c

@@ -0,0 +1,15 @@
+#ifdef RGBLIGHT_ENABLE
+
+#include QMK_KEYBOARD_H
+#include <stdio.h>
+
+extern rgblight_config_t rgblight_config;
+char rbf_info_str[24];
+const char *read_rgb_info(void) {
+
+  snprintf(rbf_info_str, sizeof(rbf_info_str), "%s %2d h%3d s%3d v%3d",
+    rgblight_config.enable ? "on" : "- ", rgblight_config.mode,
+    rgblight_config.hue, rgblight_config.sat, rgblight_config.val);
+  return rbf_info_str;
+}
+#endif

keyboards/claw44/lib/timelogger.c

@@ -0,0 +1,16 @@
+#include <stdio.h>
+#include "claw44.h"
+
+char timelog_str[24] = {};
+int last_time = 0;
+int elapsed_time = 0;
+
+void set_timelog(void) {
+  elapsed_time = timer_elapsed(last_time);
+  last_time = timer_read();
+  snprintf(timelog_str, sizeof(timelog_str), "lt:%5d, et:%5d", last_time, elapsed_time);
+}
+
+const char *read_timelog(void) {
+  return timelog_str;
+}

keyboards/claw44/readme.md

@@ -0,0 +1,15 @@
+# Claw44
+
+![Claw44](https://i.imgur.com/5a8iogl.jpg)
+
+A split keyboard with 3x6 vertically staggered keys and 4 thumb keys.
+
+Keyboard Maintainer: [@yfuku_](https://twitter.com/yfuku_)  
+Hardware Supported: Claw44 PCB, ProMicro  
+Hardware Availability: https://yfuku.booth.pm/  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make claw44:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/claw44/rev1/config.h

@@ -0,0 +1,76 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+Copyright 2015 Jack Humbert
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x3060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    yfuku
+#define PRODUCT         claw44
+#define DESCRIPTION     A split keyboard with 3x6 vertically staggered keys and 4 thumb keys
+
+/* key matrix size */
+// Rows are doubled-up
+#define MATRIX_ROWS 8
+#define MATRIX_COLS 7
+#define MATRIX_ROW_PINS { D4, C6, D7, E6 }
+
+// wiring of each half
+#define MATRIX_COL_PINS { F4, F5, F6, F7, B1, B3, B2 }
+// #define MATRIX_COL_PINS { B2, B3, B1, F7, F6, F5, F4 } //uncomment this line and comment line above if you need to reverse left-to-right key order
+
+/* define if matrix has ghost */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+// #define BACKLIGHT_LEVELS 3
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+//#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+//#define LOCKING_RESYNC_ENABLE
+
+/* ws2812 RGB LED */
+/*
+#define RGB_DI_PIN D3
+
+#define RGBLED_NUM 12    // Number of LEDs
+*/
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+// #define NO_DEBUG
+
+/* disable print */
+// #define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION

keyboards/claw44/rev1/matrix.c

@@ -0,0 +1,357 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+/*
+ * scan matrix
+ */
+#include <stdint.h>
+#include <stdbool.h>
+#include <string.h>
+#include <avr/io.h>
+#include <avr/wdt.h>
+#include <avr/interrupt.h>
+#include <util/delay.h>
+#include "print.h"
+#include "debug.h"
+#include "util.h"
+#include "matrix.h"
+#include "split_util.h"
+#include "pro_micro.h"
+
+#ifdef USE_MATRIX_I2C
+#  include "i2c.h"
+#else // USE_SERIAL
+#  include "split_scomm.h"
+#endif
+
+#ifndef DEBOUNCE
+#  define DEBOUNCE	5
+#endif
+
+#define ERROR_DISCONNECT_COUNT 5
+
+static uint8_t debouncing = DEBOUNCE;
+static const int ROWS_PER_HAND = MATRIX_ROWS/2;
+static uint8_t error_count = 0;
+uint8_t is_master = 0 ;
+
+static const uint8_t row_pins[MATRIX_ROWS] = MATRIX_ROW_PINS;
+static const uint8_t col_pins[MATRIX_COLS] = MATRIX_COL_PINS;
+
+/* matrix state(1:on, 0:off) */
+static matrix_row_t matrix[MATRIX_ROWS];
+static matrix_row_t matrix_debouncing[MATRIX_ROWS];
+
+static matrix_row_t read_cols(void);
+static void init_cols(void);
+static void unselect_rows(void);
+static void select_row(uint8_t row);
+static uint8_t matrix_master_scan(void);
+
+
+__attribute__ ((weak))
+void matrix_init_kb(void) {
+    matrix_init_user();
+}
+
+__attribute__ ((weak))
+void matrix_scan_kb(void) {
+    matrix_scan_user();
+}
+
+__attribute__ ((weak))
+void matrix_init_user(void) {
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+inline
+uint8_t matrix_rows(void)
+{
+    return MATRIX_ROWS;
+}
+
+inline
+uint8_t matrix_cols(void)
+{
+    return MATRIX_COLS;
+}
+
+void matrix_init(void)
+{
+    debug_enable = true;
+    debug_matrix = true;
+    debug_mouse = true;
+    // initialize row and col
+    unselect_rows();
+    init_cols();
+
+    TX_RX_LED_INIT;
+    TXLED0;
+    RXLED0;
+
+    // initialize matrix state: all keys off
+    for (uint8_t i=0; i < MATRIX_ROWS; i++) {
+        matrix[i] = 0;
+        matrix_debouncing[i] = 0;
+    }
+
+    is_master = has_usb();
+
+    matrix_init_quantum();
+}
+
+uint8_t _matrix_scan(void)
+{
+    // Right hand is stored after the left in the matirx so, we need to offset it
+    int offset = isLeftHand ? 0 : (ROWS_PER_HAND);
+
+    for (uint8_t i = 0; i < ROWS_PER_HAND; i++) {
+        select_row(i);
+        _delay_us(30);  // without this wait read unstable value.
+        matrix_row_t cols = read_cols();
+        if (matrix_debouncing[i+offset] != cols) {
+            matrix_debouncing[i+offset] = cols;
+            debouncing = DEBOUNCE;
+        }
+        unselect_rows();
+    }
+
+    if (debouncing) {
+        if (--debouncing) {
+            _delay_ms(1);
+        } else {
+            for (uint8_t i = 0; i < ROWS_PER_HAND; i++) {
+                matrix[i+offset] = matrix_debouncing[i+offset];
+            }
+        }
+    }
+
+    return 1;
+}
+
+#ifdef USE_MATRIX_I2C
+
+// Get rows from other half over i2c
+int i2c_transaction(void) {
+    int slaveOffset = (isLeftHand) ? (ROWS_PER_HAND) : 0;
+
+    int err = i2c_master_start(SLAVE_I2C_ADDRESS + I2C_WRITE);
+    if (err) goto i2c_error;
+
+    // start of matrix stored at 0x00
+    err = i2c_master_write(0x00);
+    if (err) goto i2c_error;
+
+    // Start read
+    err = i2c_master_start(SLAVE_I2C_ADDRESS + I2C_READ);
+    if (err) goto i2c_error;
+
+    if (!err) {
+        int i;
+        for (i = 0; i < ROWS_PER_HAND-1; ++i) {
+            matrix[slaveOffset+i] = i2c_master_read(I2C_ACK);
+        }
+        matrix[slaveOffset+i] = i2c_master_read(I2C_NACK);
+        i2c_master_stop();
+    } else {
+i2c_error: // the cable is disconnceted, or something else went wrong
+        i2c_reset_state();
+        return err;
+    }
+
+    return 0;
+}
+
+#else // USE_SERIAL
+
+int serial_transaction(int master_changed) {
+    int slaveOffset = (isLeftHand) ? (ROWS_PER_HAND) : 0;
+#ifdef SERIAL_USE_MULTI_TRANSACTION
+    int ret=serial_update_buffers(master_changed);
+#else
+    int ret=serial_update_buffers();
+#endif
+    if (ret ) {
+        if(ret==2) RXLED1;
+        return 1;
+    }
+    RXLED0;
+    memcpy(&matrix[slaveOffset],
+        (void *)serial_slave_buffer, SERIAL_SLAVE_BUFFER_LENGTH);
+    return 0;
+}
+#endif
+
+uint8_t matrix_scan(void)
+{
+    if (is_master) {
+        matrix_master_scan();
+    }else{
+        matrix_slave_scan();
+        int offset = (isLeftHand) ? ROWS_PER_HAND : 0;
+        memcpy(&matrix[offset],
+               (void *)serial_master_buffer, SERIAL_MASTER_BUFFER_LENGTH);
+        matrix_scan_quantum();
+    }
+    return 1;
+}
+
+
+uint8_t matrix_master_scan(void) {
+
+    int ret = _matrix_scan();
+    int mchanged = 1;
+
+    int offset = (isLeftHand) ? 0 : ROWS_PER_HAND;
+
+#ifdef USE_MATRIX_I2C
+//    for (int i = 0; i < ROWS_PER_HAND; ++i) {
+        /* i2c_slave_buffer[i] = matrix[offset+i]; */
+//        i2c_slave_buffer[i] = matrix[offset+i];
+//    }
+#else // USE_SERIAL
+  #ifdef SERIAL_USE_MULTI_TRANSACTION
+    mchanged = memcmp((void *)serial_master_buffer,
+		      &matrix[offset], SERIAL_MASTER_BUFFER_LENGTH);
+  #endif
+    memcpy((void *)serial_master_buffer,
+	   &matrix[offset], SERIAL_MASTER_BUFFER_LENGTH);
+#endif
+
+#ifdef USE_MATRIX_I2C
+    if( i2c_transaction() ) {
+#else // USE_SERIAL
+    if( serial_transaction(mchanged) ) {
+#endif
+        // turn on the indicator led when halves are disconnected
+        TXLED1;
+
+        error_count++;
+
+        if (error_count > ERROR_DISCONNECT_COUNT) {
+            // reset other half if disconnected
+            int slaveOffset = (isLeftHand) ? (ROWS_PER_HAND) : 0;
+            for (int i = 0; i < ROWS_PER_HAND; ++i) {
+                matrix[slaveOffset+i] = 0;
+            }
+        }
+    } else {
+        // turn off the indicator led on no error
+        TXLED0;
+        error_count = 0;
+    }
+    matrix_scan_quantum();
+    return ret;
+}
+
+void matrix_slave_scan(void) {
+    _matrix_scan();
+
+    int offset = (isLeftHand) ? 0 : ROWS_PER_HAND;
+
+#ifdef USE_MATRIX_I2C
+    for (int i = 0; i < ROWS_PER_HAND; ++i) {
+        /* i2c_slave_buffer[i] = matrix[offset+i]; */
+        i2c_slave_buffer[i] = matrix[offset+i];
+    }
+#else // USE_SERIAL
+  #ifdef SERIAL_USE_MULTI_TRANSACTION
+    int change = 0;
+  #endif
+    for (int i = 0; i < ROWS_PER_HAND; ++i) {
+  #ifdef SERIAL_USE_MULTI_TRANSACTION
+        if( serial_slave_buffer[i] != matrix[offset+i] )
+	    change = 1;
+  #endif
+        serial_slave_buffer[i] = matrix[offset+i];
+    }
+  #ifdef SERIAL_USE_MULTI_TRANSACTION
+    slave_buffer_change_count += change;
+  #endif
+#endif
+}
+
+bool matrix_is_modified(void)
+{
+    if (debouncing) return false;
+    return true;
+}
+
+inline
+bool matrix_is_on(uint8_t row, uint8_t col)
+{
+    return (matrix[row] & ((matrix_row_t)1<<col));
+}
+
+inline
+matrix_row_t matrix_get_row(uint8_t row)
+{
+    return matrix[row];
+}
+
+void matrix_print(void)
+{
+    print("\nr/c 0123456789ABCDEF\n");
+    for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+        phex(row); print(": ");
+        pbin_reverse16(matrix_get_row(row));
+        print("\n");
+    }
+}
+
+uint8_t matrix_key_count(void)
+{
+    uint8_t count = 0;
+    for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+        count += bitpop16(matrix[i]);
+    }
+    return count;
+}
+
+static void  init_cols(void)
+{
+    for(int x = 0; x < MATRIX_COLS; x++) {
+        _SFR_IO8((col_pins[x] >> 4) + 1) &=  ~_BV(col_pins[x] & 0xF);
+        _SFR_IO8((col_pins[x] >> 4) + 2) |= _BV(col_pins[x] & 0xF);
+    }
+}
+
+static matrix_row_t read_cols(void)
+{
+    matrix_row_t result = 0;
+    for(int x = 0; x < MATRIX_COLS; x++) {
+        result |= (_SFR_IO8(col_pins[x] >> 4) & _BV(col_pins[x] & 0xF)) ? 0 : (1 << x);
+    }
+    return result;
+}
+
+static void unselect_rows(void)
+{
+    for(int x = 0; x < ROWS_PER_HAND; x++) {
+        _SFR_IO8((row_pins[x] >> 4) + 1) &=  ~_BV(row_pins[x] & 0xF);
+        _SFR_IO8((row_pins[x] >> 4) + 2) |= _BV(row_pins[x] & 0xF);
+    }
+}
+
+static void select_row(uint8_t row)
+{
+    _SFR_IO8((row_pins[row] >> 4) + 1) |=  _BV(row_pins[row] & 0xF);
+    _SFR_IO8((row_pins[row] >> 4) + 2) &= ~_BV(row_pins[row] & 0xF);
+}

keyboards/claw44/rev1/rev1.c

@@ -0,0 +1,8 @@
+#include "claw44.h"
+
+#ifdef SSD1306OLED
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+  //led_set_user(usb_led);
+}
+#endif

keyboards/claw44/rev1/rev1.h

@@ -0,0 +1,57 @@
+#pragma once
+
+#include "../claw44.h"
+
+//void promicro_bootloader_jmp(bool program);
+#include "quantum.h"
+
+#ifdef RGBLIGHT_ENABLE
+//rgb led driver
+#include "ws2812.h"
+#endif
+
+#ifdef USE_I2C
+#include <stddef.h>
+#ifdef __AVR__
+	#include <avr/io.h>
+	#include <avr/interrupt.h>
+#endif
+#endif
+
+//void promicro_bootloader_jmp(bool program);
+#define LAYOUT( \
+  L00, L01, L02, L03, L04, L05,           R00, R01, R02, R03, R04, R05, \
+  L10, L11, L12, L13, L14, L15,           R10, R11, R12, R13, R14, R15, \
+  L20, L21, L22, L23, L24, L25,           R20, R21, R22, R23, R24, R25, \
+                 L30, L31, L32, L33, R30, R31, R32, R33 \
+  ) \
+  { \
+    { L00, L01, L02, L03, L04, L05 }, \
+    { L10, L11, L12, L13, L14, L15 }, \
+    { L20, L21, L22, L23, L24, L25 }, \
+    { KC_NO, KC_NO, L30, L31, L32, L33 }, \
+    { R05, R04, R03, R02, R01, R00 }, \
+    { R15, R14, R13, R12, R11, R10 }, \
+    { R25, R24, R23, R22, R21, R20 }, \
+    { KC_NO, KC_NO, R33, R32, R31, R30 } \
+  }
+
+#define LAYOUT_kc( \
+  L00, L01, L02, L03, L04, L05,           R00, R01, R02, R03, R04, R05, \
+  L10, L11, L12, L13, L14, L15,           R10, R11, R12, R13, R14, R15, \
+  L20, L21, L22, L23, L24, L25,           R20, R21, R22, R23, R24, R25, \
+                 L30, L31, L32, L33, R30, R31, R32, R33 \
+  ) \
+  LAYOUT( \
+    KC_##L00, KC_##L01, KC_##L02, KC_##L03, KC_##L04, KC_##L05,                     KC_##R00, KC_##R01, KC_##R02, KC_##R03, KC_##R04, KC_##R05, \
+    KC_##L10, KC_##L11, KC_##L12, KC_##L13, KC_##L14, KC_##L15,                     KC_##R10, KC_##R11, KC_##R12, KC_##R13, KC_##R14, KC_##R15, \
+    KC_##L20, KC_##L21, KC_##L22, KC_##L23, KC_##L24, KC_##L25,                     KC_##R20, KC_##R21, KC_##R22, KC_##R23, KC_##R24, KC_##R25, \
+                                  KC_##L30, KC_##L31, KC_##L32, KC_##L33, KC_##R30, KC_##R31, KC_##R32, KC_##R33 \
+  )
+
+enum layer_number {
+  _QWERTY = 0,
+  _LOWER,
+  _RAISE,
+  _ADJUST,
+};

keyboards/claw44/rev1/rules.mk

@@ -0,0 +1,31 @@
+SRC += rev1/matrix.c
+SRC += rev1/split_util.c
+SRC += rev1/split_scomm.c
+
+# Build Options
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no        # Mouse keys(+4700)
+EXTRAKEY_ENABLE = no        # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no         # Commands for debug and configuration
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight.
+SWAP_HANDS_ENABLE = no      # Enable one-hand typing
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+# If you want to change the display of OLED, you need to change here
+SRC += ./lib/glcdfont.c \
+       ./lib/layer_state_reader.c \
+       ./lib/logo_reader.c \
+       ./lib/keylogger.c \
+       # ./lib/rgb_state_reader.c \
+       # ./lib/mode_icon_reader.c \
+       # ./lib/host_led_state_reader.c \
+       # ./lib/timelogger.c \

keyboards/claw44/rev1/serial_config.h

@@ -0,0 +1,4 @@
+#ifndef SOFT_SERIAL_PIN
+#define SOFT_SERIAL_PIN D2
+#define SERIAL_USE_MULTI_TRANSACTION
+#endif

keyboards/claw44/rev1/split_scomm.c

@@ -0,0 +1,91 @@
+#ifdef USE_SERIAL
+#ifdef SERIAL_USE_MULTI_TRANSACTION
+/* --- USE flexible API (using multi-type transaction function) --- */
+
+#include <stdbool.h>
+#include <stdint.h>
+#include <stddef.h>
+#include <split_scomm.h>
+#include "serial.h"
+#ifdef CONSOLE_ENABLE
+  #include <print.h>
+#endif
+
+uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0};
+uint8_t volatile serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH] = {0};
+uint8_t volatile status_com = 0;
+uint8_t volatile status1 = 0;
+uint8_t slave_buffer_change_count = 0;
+uint8_t s_change_old = 0xff;
+uint8_t s_change_new = 0xff;
+
+SSTD_t transactions[] = {
+#define GET_SLAVE_STATUS 0
+    /* master buffer not changed, only recive slave_buffer_change_count */
+    { (uint8_t *)&status_com,
+      0, NULL,
+      sizeof(slave_buffer_change_count), &slave_buffer_change_count,
+    },
+#define PUT_MASTER_GET_SLAVE_STATUS 1
+    /* master buffer changed need send, and recive slave_buffer_change_count  */
+    { (uint8_t *)&status_com,
+      sizeof(serial_master_buffer), (uint8_t *)serial_master_buffer,
+      sizeof(slave_buffer_change_count), &slave_buffer_change_count,
+    },
+#define GET_SLAVE_BUFFER 2
+    /* recive serial_slave_buffer */
+    { (uint8_t *)&status1,
+      0, NULL,
+      sizeof(serial_slave_buffer), (uint8_t *)serial_slave_buffer
+    }
+};
+
+void serial_master_init(void)
+{
+    soft_serial_initiator_init(transactions, TID_LIMIT(transactions));
+}
+
+void serial_slave_init(void)
+{
+    soft_serial_target_init(transactions, TID_LIMIT(transactions));
+}
+
+// 0 => no error
+// 1 => slave did not respond
+// 2 => checksum error
+int serial_update_buffers(int master_update)
+{
+    int status, smatstatus;
+    static int need_retry = 0;
+
+    if( s_change_old != s_change_new ) {
+        smatstatus = soft_serial_transaction(GET_SLAVE_BUFFER);
+        if( smatstatus == TRANSACTION_END ) {
+            s_change_old = s_change_new;
+#ifdef CONSOLE_ENABLE
+            uprintf("slave matrix = %b %b %b %b\n",
+                    serial_slave_buffer[0], serial_slave_buffer[1],
+                    serial_slave_buffer[2], serial_slave_buffer[3]);
+#endif
+        }
+    } else {
+        // serial_slave_buffer dosen't change
+        smatstatus = TRANSACTION_END; // dummy status
+    }
+
+    if( !master_update && !need_retry) {
+        status = soft_serial_transaction(GET_SLAVE_STATUS);
+    } else {
+        status = soft_serial_transaction(PUT_MASTER_GET_SLAVE_STATUS);
+    }
+    if( status == TRANSACTION_END ) {
+        s_change_new = slave_buffer_change_count;
+        need_retry = 0;
+    } else {
+        need_retry = 1;
+    }
+    return smatstatus;
+}
+
+#endif // SERIAL_USE_MULTI_TRANSACTION
+#endif /* USE_SERIAL */

keyboards/claw44/rev1/split_scomm.h

@@ -0,0 +1,24 @@
+#ifndef SPLIT_COMM_H
+#define SPLIT_COMM_H
+
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+/* --- USE Simple API (OLD API, compatible with let's split serial.c) --- */
+#include "serial.h"
+
+#else
+/* --- USE flexible API (using multi-type transaction function) --- */
+// Buffers for master - slave communication
+#define SERIAL_SLAVE_BUFFER_LENGTH MATRIX_ROWS/2
+#define SERIAL_MASTER_BUFFER_LENGTH MATRIX_ROWS/2
+
+extern volatile uint8_t serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH];
+extern volatile uint8_t serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH];
+extern uint8_t slave_buffer_change_count;
+
+void serial_master_init(void);
+void serial_slave_init(void);
+int serial_update_buffers(int master_changed);
+
+#endif
+
+#endif /* SPLIT_COMM_H */

keyboards/claw44/rev1/split_util.c

@@ -0,0 +1,70 @@
+#include <avr/io.h>
+#include <avr/wdt.h>
+#include <avr/power.h>
+#include <avr/interrupt.h>
+#include <util/delay.h>
+#include <avr/eeprom.h>
+#include "split_util.h"
+#include "matrix.h"
+#include "keyboard.h"
+
+#ifdef USE_MATRIX_I2C
+#  include "i2c.h"
+#else
+#  include "split_scomm.h"
+#endif
+
+volatile bool isLeftHand = true;
+
+static void setup_handedness(void) {
+  #ifdef EE_HANDS
+    isLeftHand = eeprom_read_byte(EECONFIG_HANDEDNESS);
+  #else
+    // I2C_MASTER_RIGHT is deprecated, use MASTER_RIGHT instead, since this works for both serial and i2c
+    #if defined(I2C_MASTER_RIGHT) || defined(MASTER_RIGHT)
+      isLeftHand = !has_usb();
+    #else
+      isLeftHand = has_usb();
+    #endif
+  #endif
+}
+
+static void keyboard_master_setup(void) {
+
+#ifdef USE_MATRIX_I2C
+    i2c_master_init();
+#else
+    serial_master_init();
+#endif
+}
+
+static void keyboard_slave_setup(void) {
+
+#ifdef USE_MATRIX_I2C
+    i2c_slave_init(SLAVE_I2C_ADDRESS);
+#else
+    serial_slave_init();
+#endif
+}
+
+bool has_usb(void) {
+   USBCON |= (1 << OTGPADE); //enables VBUS pad
+   _delay_us(5);
+   return (USBSTA & (1<<VBUS));  //checks state of VBUS
+}
+
+void split_keyboard_setup(void) {
+   setup_handedness();
+
+   if (has_usb()) {
+      keyboard_master_setup();
+   } else {
+      keyboard_slave_setup();
+   }
+   sei();
+}
+
+// this code runs before the usb and keyboard is initialized
+void matrix_setup(void) {
+    split_keyboard_setup();
+}

keyboards/claw44/rev1/split_util.h

@@ -0,0 +1,19 @@
+#ifndef SPLIT_KEYBOARD_UTIL_H
+#define SPLIT_KEYBOARD_UTIL_H
+
+#include <stdbool.h>
+#include "eeconfig.h"
+
+#define SLAVE_I2C_ADDRESS           0x32
+
+extern volatile bool isLeftHand;
+
+// slave version of matix scan, defined in matrix.c
+void matrix_slave_scan(void);
+
+void split_keyboard_setup(void);
+bool has_usb(void);
+
+void matrix_master_OLED_init (void);
+
+#endif

keyboards/claw44/rules.mk

@@ -0,0 +1,74 @@
+SRC += i2c.c
+SRC += serial.c
+SRC += ssd1306.c
+
+# if firmware size over limit, try this option
+# CFLAGS += -flto
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = caterina
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = no       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight. 
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+CUSTOM_MATRIX = yes
+
+DEFAULT_FOLDER = claw44/rev1

keyboards/claw44/serial.c

@@ -0,0 +1,590 @@
+/*
+ * WARNING: be careful changing this code, it is very timing dependent
+ *
+ * 2018-10-28 checked
+ *  avr-gcc 4.9.2
+ *  avr-gcc 5.4.0
+ *  avr-gcc 7.3.0
+ */
+
+#ifndef F_CPU
+#define F_CPU 16000000
+#endif
+
+#include <avr/io.h>
+#include <avr/interrupt.h>
+#include <util/delay.h>
+#include <stddef.h>
+#include <stdbool.h>
+#include "serial.h"
+//#include <pro_micro.h>
+
+#ifdef SOFT_SERIAL_PIN
+
+#ifdef __AVR_ATmega32U4__
+  // if using ATmega32U4 I2C, can not use PD0 and PD1 in soft serial.
+  #ifdef USE_I2C
+    #if SOFT_SERIAL_PIN == D0 || SOFT_SERIAL_PIN == D1
+      #error Using ATmega32U4 I2C, so can not use PD0, PD1
+    #endif
+  #endif
+
+  #if SOFT_SERIAL_PIN >= D0 && SOFT_SERIAL_PIN <= D3
+    #define SERIAL_PIN_DDR   DDRD
+    #define SERIAL_PIN_PORT  PORTD
+    #define SERIAL_PIN_INPUT PIND
+    #if SOFT_SERIAL_PIN == D0
+      #define SERIAL_PIN_MASK _BV(PD0)
+      #define EIMSK_BIT       _BV(INT0)
+      #define EICRx_BIT       (~(_BV(ISC00) | _BV(ISC01)))
+      #define SERIAL_PIN_INTERRUPT INT0_vect
+    #elif  SOFT_SERIAL_PIN == D1
+      #define SERIAL_PIN_MASK _BV(PD1)
+      #define EIMSK_BIT       _BV(INT1)
+      #define EICRx_BIT       (~(_BV(ISC10) | _BV(ISC11)))
+      #define SERIAL_PIN_INTERRUPT INT1_vect
+    #elif  SOFT_SERIAL_PIN == D2
+      #define SERIAL_PIN_MASK _BV(PD2)
+      #define EIMSK_BIT       _BV(INT2)
+      #define EICRx_BIT       (~(_BV(ISC20) | _BV(ISC21)))
+      #define SERIAL_PIN_INTERRUPT INT2_vect
+    #elif  SOFT_SERIAL_PIN == D3
+      #define SERIAL_PIN_MASK _BV(PD3)
+      #define EIMSK_BIT       _BV(INT3)
+      #define EICRx_BIT       (~(_BV(ISC30) | _BV(ISC31)))
+      #define SERIAL_PIN_INTERRUPT INT3_vect
+    #endif
+  #elif  SOFT_SERIAL_PIN == E6
+    #define SERIAL_PIN_DDR   DDRE
+    #define SERIAL_PIN_PORT  PORTE
+    #define SERIAL_PIN_INPUT PINE
+    #define SERIAL_PIN_MASK  _BV(PE6)
+    #define EIMSK_BIT        _BV(INT6)
+    #define EICRx_BIT        (~(_BV(ISC60) | _BV(ISC61)))
+    #define SERIAL_PIN_INTERRUPT INT6_vect
+  #else
+  #error invalid SOFT_SERIAL_PIN value
+  #endif
+
+#else
+ #error serial.c now support ATmega32U4 only
+#endif
+
+//////////////// for backward compatibility ////////////////////////////////
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+/* --- USE Simple API (OLD API, compatible with let's split serial.c) */
+  #if SERIAL_SLAVE_BUFFER_LENGTH > 0
+  uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0};
+  #endif
+  #if SERIAL_MASTER_BUFFER_LENGTH > 0
+  uint8_t volatile serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH] = {0};
+  #endif
+  uint8_t volatile status0 = 0;
+
+SSTD_t transactions[] = {
+    { (uint8_t *)&status0,
+  #if SERIAL_MASTER_BUFFER_LENGTH > 0
+      sizeof(serial_master_buffer), (uint8_t *)serial_master_buffer,
+  #else
+      0, (uint8_t *)NULL,
+  #endif
+  #if SERIAL_SLAVE_BUFFER_LENGTH > 0
+      sizeof(serial_slave_buffer), (uint8_t *)serial_slave_buffer
+  #else
+      0, (uint8_t *)NULL,
+  #endif
+  }
+};
+
+void serial_master_init(void)
+{ soft_serial_initiator_init(transactions, TID_LIMIT(transactions)); }
+
+void serial_slave_init(void)
+{ soft_serial_target_init(transactions, TID_LIMIT(transactions)); }
+
+// 0 => no error
+// 1 => slave did not respond
+// 2 => checksum error
+int serial_update_buffers()
+{
+    int result;
+    result = soft_serial_transaction();
+    return result;
+}
+
+#endif // end of Simple API (OLD API, compatible with let's split serial.c)
+////////////////////////////////////////////////////////////////////////////
+
+#define ALWAYS_INLINE __attribute__((always_inline))
+#define NO_INLINE __attribute__((noinline))
+#define _delay_sub_us(x)    __builtin_avr_delay_cycles(x)
+
+// parity check
+#define ODD_PARITY 1
+#define EVEN_PARITY 0
+#define PARITY EVEN_PARITY
+
+#ifdef SERIAL_DELAY
+  // custom setup in config.h
+  // #define TID_SEND_ADJUST 2
+  // #define SERIAL_DELAY 6             // micro sec
+  // #define READ_WRITE_START_ADJUST 30 // cycles
+  // #define READ_WRITE_WIDTH_ADJUST 8 // cycles
+#else
+// ============ Standard setups ============
+
+#ifndef SELECT_SOFT_SERIAL_SPEED
+#define SELECT_SOFT_SERIAL_SPEED 1
+//  0: about 189kbps
+//  1: about 137kbps (default)
+//  2: about 75kbps
+//  3: about 39kbps
+//  4: about 26kbps
+//  5: about 20kbps
+#endif
+
+#if __GNUC__ < 6
+  #define TID_SEND_ADJUST 14
+#else
+  #define TID_SEND_ADJUST 2
+#endif
+
+#if SELECT_SOFT_SERIAL_SPEED == 0
+  // Very High speed
+  #define SERIAL_DELAY 4             // micro sec
+  #if __GNUC__ < 6
+    #define READ_WRITE_START_ADJUST 33 // cycles
+    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+  #else
+    #define READ_WRITE_START_ADJUST 34 // cycles
+    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+  #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 1
+  // High speed
+  #define SERIAL_DELAY 6             // micro sec
+  #if __GNUC__ < 6
+    #define READ_WRITE_START_ADJUST 30 // cycles
+    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+  #else
+    #define READ_WRITE_START_ADJUST 33 // cycles
+    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+  #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 2
+  // Middle speed
+  #define SERIAL_DELAY 12            // micro sec
+  #define READ_WRITE_START_ADJUST 30 // cycles
+  #if __GNUC__ < 6
+    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+  #else
+    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+  #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 3
+  // Low speed
+  #define SERIAL_DELAY 24            // micro sec
+  #define READ_WRITE_START_ADJUST 30 // cycles
+  #if __GNUC__ < 6
+    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+  #else
+    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+  #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 4
+  // Very Low speed
+  #define SERIAL_DELAY 36            // micro sec
+  #define READ_WRITE_START_ADJUST 30 // cycles
+  #if __GNUC__ < 6
+    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+  #else
+    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+  #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 5
+  // Ultra Low speed
+  #define SERIAL_DELAY 48            // micro sec
+  #define READ_WRITE_START_ADJUST 30 // cycles
+  #if __GNUC__ < 6
+    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+  #else
+    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+  #endif
+#else
+#error invalid SELECT_SOFT_SERIAL_SPEED value
+#endif /* SELECT_SOFT_SERIAL_SPEED */
+#endif /* SERIAL_DELAY */
+
+#define SERIAL_DELAY_HALF1 (SERIAL_DELAY/2)
+#define SERIAL_DELAY_HALF2 (SERIAL_DELAY - SERIAL_DELAY/2)
+
+#define SLAVE_INT_WIDTH_US 1
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+  #define SLAVE_INT_RESPONSE_TIME SERIAL_DELAY
+#else
+  #define SLAVE_INT_ACK_WIDTH_UNIT 2
+  #define SLAVE_INT_ACK_WIDTH 4
+#endif
+
+static SSTD_t *Transaction_table = NULL;
+static uint8_t Transaction_table_size = 0;
+
+inline static void serial_delay(void) ALWAYS_INLINE;
+inline static
+void serial_delay(void) {
+  _delay_us(SERIAL_DELAY);
+}
+
+inline static void serial_delay_half1(void) ALWAYS_INLINE;
+inline static
+void serial_delay_half1(void) {
+  _delay_us(SERIAL_DELAY_HALF1);
+}
+
+inline static void serial_delay_half2(void) ALWAYS_INLINE;
+inline static
+void serial_delay_half2(void) {
+  _delay_us(SERIAL_DELAY_HALF2);
+}
+
+inline static void serial_output(void) ALWAYS_INLINE;
+inline static
+void serial_output(void) {
+  SERIAL_PIN_DDR |= SERIAL_PIN_MASK;
+}
+
+// make the serial pin an input with pull-up resistor
+inline static void serial_input_with_pullup(void) ALWAYS_INLINE;
+inline static
+void serial_input_with_pullup(void) {
+  SERIAL_PIN_DDR  &= ~SERIAL_PIN_MASK;
+  SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
+}
+
+inline static uint8_t serial_read_pin(void) ALWAYS_INLINE;
+inline static
+uint8_t serial_read_pin(void) {
+  return !!(SERIAL_PIN_INPUT & SERIAL_PIN_MASK);
+}
+
+inline static void serial_low(void) ALWAYS_INLINE;
+inline static
+void serial_low(void) {
+  SERIAL_PIN_PORT &= ~SERIAL_PIN_MASK;
+}
+
+inline static void serial_high(void) ALWAYS_INLINE;
+inline static
+void serial_high(void) {
+  SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
+}
+
+void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size)
+{
+    Transaction_table = sstd_table;
+    Transaction_table_size = (uint8_t)sstd_table_size;
+    serial_output();
+    serial_high();
+}
+
+void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size)
+{
+    Transaction_table = sstd_table;
+    Transaction_table_size = (uint8_t)sstd_table_size;
+    serial_input_with_pullup();
+
+    // Enable INT0-INT3,INT6
+    EIMSK |= EIMSK_BIT;
+#if SERIAL_PIN_MASK == _BV(PE6)
+    // Trigger on falling edge of INT6
+    EICRB &= EICRx_BIT;
+#else
+    // Trigger on falling edge of INT0-INT3
+    EICRA &= EICRx_BIT;
+#endif
+}
+
+// Used by the sender to synchronize timing with the reciver.
+static void sync_recv(void) NO_INLINE;
+static
+void sync_recv(void) {
+  for (uint8_t i = 0; i < SERIAL_DELAY*5 && serial_read_pin(); i++ ) {
+  }
+  // This shouldn't hang if the target disconnects because the
+  // serial line will float to high if the target does disconnect.
+  while (!serial_read_pin());
+}
+
+// Used by the reciver to send a synchronization signal to the sender.
+static void sync_send(void) NO_INLINE;
+static
+void sync_send(void) {
+  serial_low();
+  serial_delay();
+  serial_high();
+}
+
+// Reads a byte from the serial line
+static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) NO_INLINE;
+static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) {
+    uint8_t byte, i, p, pb;
+
+  _delay_sub_us(READ_WRITE_START_ADJUST);
+  for( i = 0, byte = 0, p = PARITY; i < bit; i++ ) {
+      serial_delay_half1();   // read the middle of pulses
+      if( serial_read_pin() ) {
+          byte = (byte << 1) | 1; p ^= 1;
+      } else {
+          byte = (byte << 1) | 0; p ^= 0;
+      }
+      _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
+      serial_delay_half2();
+  }
+  /* recive parity bit */
+  serial_delay_half1();   // read the middle of pulses
+  pb = serial_read_pin();
+  _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
+  serial_delay_half2();
+
+  *pterrcount += (p != pb)? 1 : 0;
+
+  return byte;
+}
+
+// Sends a byte with MSB ordering
+void serial_write_chunk(uint8_t data, uint8_t bit) NO_INLINE;
+void serial_write_chunk(uint8_t data, uint8_t bit) {
+    uint8_t b, p;
+    for( p = PARITY, b = 1<<(bit-1); b ; b >>= 1) {
+        if(data & b) {
+            serial_high(); p ^= 1;
+        } else {
+            serial_low();  p ^= 0;
+        }
+        serial_delay();
+    }
+    /* send parity bit */
+    if(p & 1) { serial_high(); }
+    else      { serial_low(); }
+    serial_delay();
+
+    serial_low(); // sync_send() / senc_recv() need raise edge
+}
+
+static void serial_send_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
+static
+void serial_send_packet(uint8_t *buffer, uint8_t size) {
+  for (uint8_t i = 0; i < size; ++i) {
+    uint8_t data;
+    data = buffer[i];
+    sync_send();
+    serial_write_chunk(data,8);
+  }
+}
+
+static uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
+static
+uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) {
+  uint8_t pecount = 0;
+  for (uint8_t i = 0; i < size; ++i) {
+    uint8_t data;
+    sync_recv();
+    data = serial_read_chunk(&pecount, 8);
+    buffer[i] = data;
+  }
+  return pecount == 0;
+}
+
+inline static
+void change_sender2reciver(void) {
+    sync_send();          //0
+    serial_delay_half1(); //1
+    serial_low();         //2
+    serial_input_with_pullup(); //2
+    serial_delay_half1(); //3
+}
+
+inline static
+void change_reciver2sender(void) {
+    sync_recv();     //0
+    serial_delay();  //1
+    serial_low();    //3
+    serial_output(); //3
+    serial_delay_half1(); //4
+}
+
+static inline uint8_t nibble_bits_count(uint8_t bits)
+{
+    bits = (bits & 0x5) + (bits >> 1 & 0x5);
+    bits = (bits & 0x3) + (bits >> 2 & 0x3);
+    return bits;
+}
+
+// interrupt handle to be used by the target device
+ISR(SERIAL_PIN_INTERRUPT) {
+
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+  serial_low();
+  serial_output();
+  SSTD_t *trans = Transaction_table;
+#else
+  // recive transaction table index
+  uint8_t tid, bits;
+  uint8_t pecount = 0;
+  sync_recv();
+  bits = serial_read_chunk(&pecount,7);
+  tid = bits>>3;
+  bits = (bits&7) != nibble_bits_count(tid);
+  if( bits || pecount> 0 || tid > Transaction_table_size ) {
+      return;
+  }
+  serial_delay_half1();
+
+  serial_high(); // response step1 low->high
+  serial_output();
+  _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT*SLAVE_INT_ACK_WIDTH);
+  SSTD_t *trans = &Transaction_table[tid];
+  serial_low(); // response step2 ack high->low
+#endif
+
+  // target send phase
+  if( trans->target2initiator_buffer_size > 0 )
+      serial_send_packet((uint8_t *)trans->target2initiator_buffer,
+                         trans->target2initiator_buffer_size);
+  // target switch to input
+  change_sender2reciver();
+
+  // target recive phase
+  if( trans->initiator2target_buffer_size > 0 ) {
+      if (serial_recive_packet((uint8_t *)trans->initiator2target_buffer,
+                               trans->initiator2target_buffer_size) ) {
+          *trans->status = TRANSACTION_ACCEPTED;
+      } else {
+          *trans->status = TRANSACTION_DATA_ERROR;
+      }
+  } else {
+      *trans->status = TRANSACTION_ACCEPTED;
+  }
+
+  sync_recv(); //weit initiator output to high
+}
+
+/////////
+//  start transaction by initiator
+//
+// int  soft_serial_transaction(int sstd_index)
+//
+// Returns:
+//    TRANSACTION_END
+//    TRANSACTION_NO_RESPONSE
+//    TRANSACTION_DATA_ERROR
+// this code is very time dependent, so we need to disable interrupts
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+int  soft_serial_transaction(void) {
+  SSTD_t *trans = Transaction_table;
+#else
+int  soft_serial_transaction(int sstd_index) {
+  if( sstd_index > Transaction_table_size )
+      return TRANSACTION_TYPE_ERROR;
+  SSTD_t *trans = &Transaction_table[sstd_index];
+#endif
+  cli();
+
+  // signal to the target that we want to start a transaction
+  serial_output();
+  serial_low();
+  _delay_us(SLAVE_INT_WIDTH_US);
+
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+  // wait for the target response
+  serial_input_with_pullup();
+  _delay_us(SLAVE_INT_RESPONSE_TIME);
+
+  // check if the target is present
+  if (serial_read_pin()) {
+    // target failed to pull the line low, assume not present
+    serial_output();
+    serial_high();
+    *trans->status = TRANSACTION_NO_RESPONSE;
+    sei();
+    return TRANSACTION_NO_RESPONSE;
+  }
+
+#else
+  // send transaction table index
+  int tid = (sstd_index<<3) | (7 & nibble_bits_count(sstd_index));
+  sync_send();
+  _delay_sub_us(TID_SEND_ADJUST);
+  serial_write_chunk(tid, 7);
+  serial_delay_half1();
+
+  // wait for the target response (step1 low->high)
+  serial_input_with_pullup();
+  while( !serial_read_pin() ) {
+      _delay_sub_us(2);
+  }
+
+  // check if the target is present (step2 high->low)
+  for( int i = 0; serial_read_pin(); i++ ) {
+      if (i > SLAVE_INT_ACK_WIDTH + 1) {
+          // slave failed to pull the line low, assume not present
+          serial_output();
+          serial_high();
+          *trans->status = TRANSACTION_NO_RESPONSE;
+          sei();
+          return TRANSACTION_NO_RESPONSE;
+      }
+      _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT);
+  }
+#endif
+
+  // initiator recive phase
+  // if the target is present syncronize with it
+  if( trans->target2initiator_buffer_size > 0 ) {
+      if (!serial_recive_packet((uint8_t *)trans->target2initiator_buffer,
+                                trans->target2initiator_buffer_size) ) {
+          serial_output();
+          serial_high();
+          *trans->status = TRANSACTION_DATA_ERROR;
+          sei();
+          return TRANSACTION_DATA_ERROR;
+      }
+   }
+
+  // initiator switch to output
+  change_reciver2sender();
+
+  // initiator send phase
+  if( trans->initiator2target_buffer_size > 0 ) {
+      serial_send_packet((uint8_t *)trans->initiator2target_buffer,
+                         trans->initiator2target_buffer_size);
+  }
+
+  // always, release the line when not in use
+  sync_send();
+
+  *trans->status = TRANSACTION_END;
+  sei();
+  return TRANSACTION_END;
+}
+
+#ifdef SERIAL_USE_MULTI_TRANSACTION
+int soft_serial_get_and_clean_status(int sstd_index) {
+    SSTD_t *trans = &Transaction_table[sstd_index];
+    cli();
+    int retval = *trans->status;
+    *trans->status = 0;;
+    sei();
+    return retval;
+}
+#endif
+
+#endif
+
+// Helix serial.c history
+//   2018-1-29 fork from let's split and add PD2, modify sync_recv() (#2308, bceffdefc)
+//   2018-6-28 bug fix master to slave comm and speed up (#3255, 1038bbef4)
+//             (adjusted with avr-gcc 4.9.2)
+//   2018-7-13 remove USE_SERIAL_PD2 macro (#3374, f30d6dd78)
+//             (adjusted with avr-gcc 4.9.2)
+//   2018-8-11 add support multi-type transaction (#3608, feb5e4aae)
+//             (adjusted with avr-gcc 4.9.2)
+//   2018-10-21 fix serial and RGB animation conflict (#4191, 4665e4fff)
+//             (adjusted with avr-gcc 7.3.0)
+//   2018-10-28 re-adjust compiler depend value of delay (#4269, 8517f8a66)
+//             (adjusted with avr-gcc 5.4.0, 7.3.0)

keyboards/claw44/serial.h

@@ -0,0 +1,84 @@
+#ifndef SOFT_SERIAL_H
+#define SOFT_SERIAL_H
+
+#include <stdbool.h>
+
+// /////////////////////////////////////////////////////////////////
+// Need Soft Serial defines in config.h
+// /////////////////////////////////////////////////////////////////
+// ex.
+//  #define SOFT_SERIAL_PIN ??   // ?? = D0,D1,D2,D3,E6
+//  OPTIONAL: #define SELECT_SOFT_SERIAL_SPEED ? // ? = 1,2,3,4,5
+//                                               //  1: about 137kbps (default)
+//                                               //  2: about 75kbps
+//                                               //  3: about 39kbps
+//                                               //  4: about 26kbps
+//                                               //  5: about 20kbps
+//
+// //// USE Simple API (OLD API, compatible with let's split serial.c)
+// ex.
+//  #define SERIAL_SLAVE_BUFFER_LENGTH MATRIX_ROWS/2
+//  #define SERIAL_MASTER_BUFFER_LENGTH 1
+//
+// //// USE flexible API (using multi-type transaction function)
+//  #define SERIAL_USE_MULTI_TRANSACTION
+//
+// /////////////////////////////////////////////////////////////////
+
+
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+/* --- USE Simple API (OLD API, compatible with let's split serial.c) */
+#if SERIAL_SLAVE_BUFFER_LENGTH > 0
+extern volatile uint8_t serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH];
+#endif
+#if SERIAL_MASTER_BUFFER_LENGTH > 0
+extern volatile uint8_t serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH];
+#endif
+
+void serial_master_init(void);
+void serial_slave_init(void);
+int serial_update_buffers(void);
+
+#endif // USE Simple API
+
+// Soft Serial Transaction Descriptor
+typedef struct _SSTD_t  {
+    uint8_t *status;
+    uint8_t initiator2target_buffer_size;
+    uint8_t *initiator2target_buffer;
+    uint8_t target2initiator_buffer_size;
+    uint8_t *target2initiator_buffer;
+} SSTD_t;
+#define TID_LIMIT( table ) (sizeof(table) / sizeof(SSTD_t))
+
+// initiator is transaction start side
+void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size);
+// target is interrupt accept side
+void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size);
+
+// initiator resullt
+#define TRANSACTION_END 0
+#define TRANSACTION_NO_RESPONSE 0x1
+#define TRANSACTION_DATA_ERROR  0x2
+#define TRANSACTION_TYPE_ERROR  0x4
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+int  soft_serial_transaction(void);
+#else
+int  soft_serial_transaction(int sstd_index);
+#endif
+
+// target status
+// *SSTD_t.status has
+//   initiator:
+//       TRANSACTION_END
+//    or TRANSACTION_NO_RESPONSE
+//    or TRANSACTION_DATA_ERROR
+//   target:
+//       TRANSACTION_DATA_ERROR
+//    or TRANSACTION_ACCEPTED
+#define TRANSACTION_ACCEPTED 0x8
+#ifdef SERIAL_USE_MULTI_TRANSACTION
+int  soft_serial_get_and_clean_status(int sstd_index);
+#endif
+
+#endif /* SOFT_SERIAL_H */

keyboards/claw44/ssd1306.c

@@ -0,0 +1,346 @@
+#ifdef SSD1306OLED
+
+#include "ssd1306.h"
+#include "i2c.h"
+#include <string.h>
+#include "print.h"
+#ifdef ADAFRUIT_BLE_ENABLE
+#include "adafruit_ble.h"
+#endif
+#ifdef PROTOCOL_LUFA
+#include "lufa.h"
+#endif
+#include "sendchar.h"
+#include "timer.h"
+
+static const unsigned char font[] PROGMEM;
+
+// Set this to 1 to help diagnose early startup problems
+// when testing power-on with ble.  Turn it off otherwise,
+// as the latency of printing most of the debug info messes
+// with the matrix scan, causing keys to drop.
+#define DEBUG_TO_SCREEN 0
+
+//static uint16_t last_battery_update;
+//static uint32_t vbat;
+//#define BatteryUpdateInterval 10000 /* milliseconds */
+
+// 'last_flush' is declared as uint16_t,
+// so this must be less than 65535 
+#define ScreenOffInterval 60000 /* milliseconds */
+#if DEBUG_TO_SCREEN
+static uint8_t displaying;
+#endif
+static uint16_t last_flush;
+
+static bool force_dirty = true;
+
+// Write command sequence.
+// Returns true on success.
+static inline bool _send_cmd1(uint8_t cmd) {
+  bool res = false;
+
+  if (i2c_start_write(SSD1306_ADDRESS)) {
+    xprintf("failed to start write to %d\n", SSD1306_ADDRESS);
+    goto done;
+  }
+
+  if (i2c_master_write(0x0 /* command byte follows */)) {
+    print("failed to write control byte\n");
+
+    goto done;
+  }
+
+  if (i2c_master_write(cmd)) {
+    xprintf("failed to write command %d\n", cmd);
+    goto done;
+  }
+  res = true;
+done:
+  i2c_master_stop();
+  return res;
+}
+
+// Write 2-byte command sequence.
+// Returns true on success
+static inline bool _send_cmd2(uint8_t cmd, uint8_t opr) {
+  if (!_send_cmd1(cmd)) {
+    return false;
+  }
+  return _send_cmd1(opr);
+}
+
+// Write 3-byte command sequence.
+// Returns true on success
+static inline bool _send_cmd3(uint8_t cmd, uint8_t opr1, uint8_t opr2) {
+  if (!_send_cmd1(cmd)) {
+    return false;
+  }
+  if (!_send_cmd1(opr1)) {
+    return false;
+  }
+  return _send_cmd1(opr2);
+}
+
+#define send_cmd1(c) if (!_send_cmd1(c)) {goto done;}
+#define send_cmd2(c,o) if (!_send_cmd2(c,o)) {goto done;}
+#define send_cmd3(c,o1,o2) if (!_send_cmd3(c,o1,o2)) {goto done;}
+
+static void clear_display(void) {
+  matrix_clear(&display);
+
+  // Clear all of the display bits (there can be random noise
+  // in the RAM on startup)
+  send_cmd3(PageAddr, 0, (DisplayHeight / 8) - 1);
+  send_cmd3(ColumnAddr, 0, DisplayWidth - 1);
+
+  if (i2c_start_write(SSD1306_ADDRESS)) {
+    goto done;
+  }
+  if (i2c_master_write(0x40)) {
+    // Data mode
+    goto done;
+  }
+  for (uint8_t row = 0; row < MatrixRows; ++row) {
+    for (uint8_t col = 0; col < DisplayWidth; ++col) {
+      i2c_master_write(0);
+    }
+  }
+
+  display.dirty = false;
+
+done:
+  i2c_master_stop();
+}
+
+#if DEBUG_TO_SCREEN
+#undef sendchar
+static int8_t capture_sendchar(uint8_t c) {
+  sendchar(c);
+  iota_gfx_write_char(c);
+
+  if (!displaying) {
+    iota_gfx_flush();
+  }
+  return 0;
+}
+#endif
+
+bool iota_gfx_init(bool rotate) {
+  bool success = false;
+
+  i2c_master_init();
+  send_cmd1(DisplayOff);
+  send_cmd2(SetDisplayClockDiv, 0x80);
+  send_cmd2(SetMultiPlex, DisplayHeight - 1);
+
+  send_cmd2(SetDisplayOffset, 0);
+
+
+  send_cmd1(SetStartLine | 0x0);
+  send_cmd2(SetChargePump, 0x14 /* Enable */);
+  send_cmd2(SetMemoryMode, 0 /* horizontal addressing */);
+
+  if(rotate){
+    // the following Flip the display orientation 180 degrees
+    send_cmd1(SegRemap);
+    send_cmd1(ComScanInc);
+  }else{
+    // Flips the display orientation 0 degrees
+    send_cmd1(SegRemap | 0x1);
+    send_cmd1(ComScanDec);
+  }
+
+  send_cmd2(SetComPins, 0x2);
+  send_cmd2(SetContrast, 0x8f);
+  send_cmd2(SetPreCharge, 0xf1);
+  send_cmd2(SetVComDetect, 0x40);
+  send_cmd1(DisplayAllOnResume);
+  send_cmd1(NormalDisplay);
+  send_cmd1(DeActivateScroll);
+  send_cmd1(DisplayOn);
+
+  send_cmd2(SetContrast, 0); // Dim
+
+  clear_display();
+
+  success = true;
+
+  iota_gfx_flush();
+
+#if DEBUG_TO_SCREEN
+  print_set_sendchar(capture_sendchar);
+#endif
+
+done:
+  return success;
+}
+
+bool iota_gfx_off(void) {
+  bool success = false;
+
+  send_cmd1(DisplayOff);
+  success = true;
+
+done:
+  return success;
+}
+
+bool iota_gfx_on(void) {
+  bool success = false;
+
+  send_cmd1(DisplayOn);
+  success = true;
+
+done:
+  return success;
+}
+
+void matrix_write_char_inner(struct CharacterMatrix *matrix, uint8_t c) {
+  *matrix->cursor = c;
+  ++matrix->cursor;
+
+  if (matrix->cursor - &matrix->display[0][0] == sizeof(matrix->display)) {
+    // We went off the end; scroll the display upwards by one line
+    memmove(&matrix->display[0], &matrix->display[1],
+            MatrixCols * (MatrixRows - 1));
+    matrix->cursor = &matrix->display[MatrixRows - 1][0];
+    memset(matrix->cursor, ' ', MatrixCols);
+  }
+}
+
+void matrix_write_char(struct CharacterMatrix *matrix, uint8_t c) {
+  matrix->dirty = true;
+
+  if (c == '\n') {
+    // Clear to end of line from the cursor and then move to the
+    // start of the next line
+    uint8_t cursor_col = (matrix->cursor - &matrix->display[0][0]) % MatrixCols;
+
+    while (cursor_col++ < MatrixCols) {
+      matrix_write_char_inner(matrix, ' ');
+    }
+    return;
+  }
+
+  matrix_write_char_inner(matrix, c);
+}
+
+void iota_gfx_write_char(uint8_t c) {
+  matrix_write_char(&display, c);
+}
+
+void matrix_write(struct CharacterMatrix *matrix, const char *data) {
+  const char *end = data + strlen(data);
+  while (data < end) {
+    matrix_write_char(matrix, *data);
+    ++data;
+  }
+}
+
+void matrix_write_ln(struct CharacterMatrix *matrix, const char *data) {
+  char data_ln[strlen(data)+2];
+  snprintf(data_ln, sizeof(data_ln), "%s\n", data);
+  matrix_write(matrix, data_ln);
+}
+
+void iota_gfx_write(const char *data) {
+  matrix_write(&display, data);
+}
+
+void matrix_write_P(struct CharacterMatrix *matrix, const char *data) {
+  while (true) {
+    uint8_t c = pgm_read_byte(data);
+    if (c == 0) {
+      return;
+    }
+    matrix_write_char(matrix, c);
+    ++data;
+  }
+}
+
+void iota_gfx_write_P(const char *data) {
+  matrix_write_P(&display, data);
+}
+
+void matrix_clear(struct CharacterMatrix *matrix) {
+  memset(matrix->display, ' ', sizeof(matrix->display));
+  matrix->cursor = &matrix->display[0][0];
+  matrix->dirty = true;
+}
+
+void iota_gfx_clear_screen(void) {
+  matrix_clear(&display);
+}
+
+void matrix_render(struct CharacterMatrix *matrix) {
+  last_flush = timer_read();
+  iota_gfx_on();
+#if DEBUG_TO_SCREEN
+  ++displaying;
+#endif
+
+  // Move to the home position
+  send_cmd3(PageAddr, 0, MatrixRows - 1);
+  send_cmd3(ColumnAddr, 0, (MatrixCols * FontWidth) - 1);
+
+  if (i2c_start_write(SSD1306_ADDRESS)) {
+    goto done;
+  }
+  if (i2c_master_write(0x40)) {
+    // Data mode
+    goto done;
+  }
+
+  for (uint8_t row = 0; row < MatrixRows; ++row) {
+    for (uint8_t col = 0; col < MatrixCols; ++col) {
+      const uint8_t *glyph = font + (matrix->display[row][col] * FontWidth);
+
+      for (uint8_t glyphCol = 0; glyphCol < FontWidth; ++glyphCol) {
+        uint8_t colBits = pgm_read_byte(glyph + glyphCol);
+        i2c_master_write(colBits);
+      }
+
+      // 1 column of space between chars (it's not included in the glyph)
+      //i2c_master_write(0);
+    }
+  }
+
+  matrix->dirty = false;
+
+done:
+  i2c_master_stop();
+#if DEBUG_TO_SCREEN
+  --displaying;
+#endif
+}
+
+void iota_gfx_flush(void) {
+  matrix_render(&display);
+}
+
+__attribute__ ((weak))
+void iota_gfx_task_user(void) {
+}
+
+void iota_gfx_task(void) {
+  iota_gfx_task_user();
+
+  if (display.dirty|| force_dirty) {
+    iota_gfx_flush();
+    force_dirty = false;
+  }
+
+  /*
+  if (timer_elapsed(last_flush) > ScreenOffInterval) {
+    iota_gfx_off();
+  }
+  */
+}
+
+bool process_record_gfx(uint16_t keycode, keyrecord_t *record) {
+  force_dirty = true;
+  return true;
+}
+
+#endif

keyboards/claw44/ssd1306.h

@@ -0,0 +1,91 @@
+#pragma once
+
+#include <stdbool.h>
+#include <stdio.h>
+#include "pincontrol.h"
+#include "action.h"
+
+enum ssd1306_cmds {
+  DisplayOff = 0xAE,
+  DisplayOn = 0xAF,
+
+  SetContrast = 0x81,
+  DisplayAllOnResume = 0xA4,
+
+  DisplayAllOn = 0xA5,
+  NormalDisplay = 0xA6,
+  InvertDisplay = 0xA7,
+  SetDisplayOffset = 0xD3,
+  SetComPins = 0xda,
+  SetVComDetect = 0xdb,
+  SetDisplayClockDiv = 0xD5,
+  SetPreCharge = 0xd9,
+  SetMultiPlex = 0xa8,
+  SetLowColumn = 0x00,
+  SetHighColumn = 0x10,
+  SetStartLine = 0x40,
+
+  SetMemoryMode = 0x20,
+  ColumnAddr = 0x21,
+  PageAddr = 0x22,
+
+  ComScanInc = 0xc0,
+  ComScanDec = 0xc8,
+  SegRemap = 0xa0,
+  SetChargePump = 0x8d,
+  ExternalVcc = 0x01,
+  SwitchCapVcc = 0x02,
+
+  ActivateScroll = 0x2f,
+  DeActivateScroll = 0x2e,
+  SetVerticalScrollArea = 0xa3,
+  RightHorizontalScroll = 0x26,
+  LeftHorizontalScroll = 0x27,
+  VerticalAndRightHorizontalScroll = 0x29,
+  VerticalAndLeftHorizontalScroll = 0x2a,
+};
+
+// Controls the SSD1306 128x32 OLED display via i2c
+
+#ifndef SSD1306_ADDRESS
+#define SSD1306_ADDRESS 0x3C
+#endif
+
+#define DisplayHeight 32
+#define DisplayWidth 128
+
+#define FontHeight 8
+#define FontWidth 6
+
+#define MatrixRows (DisplayHeight / FontHeight)
+#define MatrixCols (DisplayWidth / FontWidth)
+
+struct CharacterMatrix {
+  uint8_t display[MatrixRows][MatrixCols];
+  uint8_t *cursor;
+  bool dirty;
+};
+
+struct CharacterMatrix display;
+
+bool iota_gfx_init(bool rotate);
+void iota_gfx_task(void);
+bool iota_gfx_off(void);
+bool iota_gfx_on(void);
+void iota_gfx_flush(void);
+void iota_gfx_write_char(uint8_t c);
+void iota_gfx_write(const char *data);
+void iota_gfx_write_P(const char *data);
+void iota_gfx_clear_screen(void);
+
+void iota_gfx_task_user(void);
+
+void matrix_clear(struct CharacterMatrix *matrix);
+void matrix_write_char_inner(struct CharacterMatrix *matrix, uint8_t c);
+void matrix_write_char(struct CharacterMatrix *matrix, uint8_t c);
+void matrix_write(struct CharacterMatrix *matrix, const char *data);
+void matrix_write_ln(struct CharacterMatrix *matrix, const char *data);
+void matrix_write_P(struct CharacterMatrix *matrix, const char *data);
+void matrix_render(struct CharacterMatrix *matrix);
+
+bool process_record_gfx(uint16_t keycode, keyrecord_t *record);

keyboards/clueboard/2x1800/keymaps/default/config.h

@@ -16,6 +16,4 @@
 
 #pragma once
 
-#include "config_common.h"
-
 // place overrides here

keyboards/clueboard/66_hotswap/gen1/config.h

@@ -80,11 +80,6 @@
  */
 //#define FORCE_NKRO
 
-/* key combination for magic key command */
-#define IS_COMMAND() ( \
-	keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)
-
 /*
  * Feature disable options
  *  These options are also useful to firmware size reduction.

keyboards/comet46/keymaps/default/config.h

@@ -18,14 +18,12 @@ You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
+
+// place overrides here
 
-// #include "../../config.h"
 
 /* Use I2C or Serial */
 
 #define USE_I2C
 #define SSD1306OLED
-
-#endif

keyboards/contra/keymaps/default/config.h

@@ -1,7 +1,5 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
 
-#include "config_common.h"
 
 #ifdef AUDIO_ENABLE
     #define STARTUP_SONG SONG(PLANCK_SOUND)
@@ -25,7 +23,7 @@
 /* enable basic MIDI features:
    - MIDI notes can be sent when in Music mode is on
 */
-                                
+
 #define MIDI_BASIC
 
 /* enable advanced MIDI features:
@@ -38,5 +36,3 @@
 
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 2
-
-#endif

keyboards/contra/keymaps/msiu/config.h

@@ -0,0 +1,37 @@
+#pragma once
+
+#ifdef AUDIO_ENABLE
+    #define STARTUP_SONG SONG(PLANCK_SOUND)
+    // #define STARTUP_SONG SONG(NO_SOUND)
+
+    #define DEFAULT_LAYER_SONGS { SONG(QWERTY_SOUND), \
+                                  SONG(COLEMAK_SOUND), \
+                                  SONG(DVORAK_SOUND) \
+                                }
+#endif
+
+#define MUSIC_MASK (keycode != KC_NO)
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+                                
+#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 2

keyboards/contra/keymaps/msiu/keymap.c

@@ -0,0 +1,175 @@
+#include QMK_KEYBOARD_H
+
+extern keymap_config_t keymap_config;
+
+enum planck_layers {
+  _QWERTY,
+  _DVORAK,
+  _LOWER,
+  _RAISE,
+  _NUMB,
+  _FUNC,
+  _ADJUST
+};
+
+enum planck_keycodes {
+  QWERTY = SAFE_RANGE,
+  DVORAK,
+  LOWER,
+  RAISE
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+  /* Qwerty
+   * ,------------------------------------------------------------------------------------------.
+   * | Tab / Numb  |   Q  |   W  |   E  |   R  |   T  |   Y  |   U  |   I  |   O  |   P  | Bksp |
+   * |-------------+------+------+------+------+-------------+------+------+------+------+------|
+   * | Esc / Ctrl  |   A  |   S  |   D  |   F  |   G  |   H  |   J  |   K  |   L  |   ;  |  '   |
+   * |-------------+------+------+------+------+------|------+------+------+------+------+------|
+   * | Shift       |   Z  |   X  |   C  |   V  |   B  |   N  |   M  |   ,  |   .  |   /  |Enter |
+   * |-------------+------+------+------+------+------+------+------+------+------+------+------|
+   * | Ctrl        |Hyper | Alt  | GUI  |Lower | Func |Space |Raise | Left | Down |  Up  |Right |
+   * `------------------------------------------------------------------------------------------'
+   */
+  [_QWERTY] = LAYOUT_ortho_4x12(
+    LT(_NUMB, KC_TAB),   KC_Q,    KC_W,    KC_E,    KC_R,  KC_T,      KC_Y,   KC_U,  KC_I,    KC_O,    KC_P,    KC_BSPC,
+    LCTL_T(KC_ESC),      KC_A,    KC_S,    KC_D,    KC_F,  KC_G,      KC_H,   KC_J,  KC_K,    KC_L,    KC_SCLN, KC_QUOT,
+    KC_LSFT,             KC_Z,    KC_X,    KC_C,    KC_V,  KC_B,      KC_N,   KC_M,  KC_COMM, KC_DOT,  KC_SLSH, KC_ENT,
+    KC_LCTL,             KC_HYPR, KC_LALT, KC_LGUI, LOWER, MO(_FUNC), KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT
+  ),
+
+  /* Dvorak
+   * ,-----------------------------------------------------------------------------------.
+   * | Tab  |   "  |   ,  |   .  |   P  |   Y  |   F  |   G  |   C  |   R  |   L  | Bksp |
+   * |------+------+------+------+------+-------------+------+------+------+------+------|
+   * | Esc  |   A  |   O  |   E  |   U  |   I  |   D  |   H  |   T  |   N  |   S  |  /   |
+   * |------+------+------+------+------+------|------+------+------+------+------+------|
+   * | Shift|   ;  |   Q  |   J  |   K  |   X  |   B  |   M  |   W  |   V  |   Z  |Enter |
+   * |------+------+------+------+------+------+------+------+------+------+------+------|
+   * | Brite| Ctrl | Alt  | GUI  |Lower |    Space    |Raise | Left | Down |  Up  |Right |
+   * `-----------------------------------------------------------------------------------'
+   */
+  [_DVORAK] = LAYOUT_ortho_4x12(
+    _______, KC_QUOT, KC_COMM, KC_DOT,  KC_P,    KC_Y,     KC_F,    KC_G,    KC_C,    KC_R,    KC_L,    _______,
+    _______, KC_A,    KC_O,    KC_E,    KC_U,    KC_I,     KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    KC_SLSH,
+    _______, KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,     KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    _______,
+    _______, _______,  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______
+  ),
+
+  /* Lower
+   * ,-----------------------------------------------------------------------------------.
+   * |   ~  |   !  |   @  |   #  |   $  |   %  |   ^  |   &  |   *  |   (  |   )  | Bksp |
+   * |------+------+------+------+------+-------------+------+------+------+------+------|
+   * | Del  |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |   _  |   +  |   {  |   }  |  |   |
+   * |------+------+------+------+------+------|------+------+------+------+------+------|
+   * |      |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |ISO ~ |ISO | | Home | End  |      |
+   * |------+------+------+------+------+------+------+------+------+------+------+------|
+   * |      |      |      |      |      |             |      | Next | Vol- | Vol+ | Play |
+   * `-----------------------------------------------------------------------------------'
+   */
+  [_LOWER] = LAYOUT_ortho_4x12(
+    KC_TILD, KC_EXLM,  KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL,
+    _______, KC_F1,    KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE,
+    _______, KC_F7,    KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_PGDN, KC_PGUP, KC_HOME, KC_END , KC_MUTE,
+    _______, _______,  _______, _______, _______, _______, KC_MPLY, _______, KC_MPRV, KC_VOLD, KC_VOLU, KC_MNXT
+  ),
+
+  /* Raise
+   * ,-----------------------------------------------------------------------------------.
+   * |   `  |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   0  | Bksp |
+   * |------+------+------+------+------+-------------+------+------+------+------+------|
+   * | Del  |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |   -  |   =  |   [  |   ]  |  \   |
+   * |------+------+------+------+------+------|------+------+------+------+------+------|
+   * |      |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |ISO # |ISO / |Pg Up |Pg Dn |      |
+   * |------+------+------+------+------+------+------+------+------+------+------+------|
+   * |      |      |      |      |      |             |      | Next | Vol- | Vol+ | Play |
+   * `-----------------------------------------------------------------------------------'
+   */
+  [_RAISE] = LAYOUT_ortho_4x12(
+    KC_GRV,  KC_1,    KC_2,    KC_3,   KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_BSPC,
+    _______, KC_4,    KC_5,    KC_6,   KC_PLUS, KC_F5,   KC_F6,   KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_BSLS,
+    _______, KC_7,    KC_8,    KC_9,   KC_MINS, KC_F11,  KC_F12,  KC_PGDN, KC_PGUP, KC_HOME, KC_END , KC_MUTE,
+    _______, _______, _______, _______, _______, _______, KC_MPLY, _______, KC_MPRV, KC_VOLD, KC_VOLU, KC_MNXT
+  ),
+
+  /* Adjust (Lower + Raise)
+   * ,-----------------------------------------------------------------------------------.
+   * |      | Reset|      |      |      |      |      |      |      |      |      |  Del |
+   * |------+------+------+------+------+-------------+------+------+------+------+------|
+   * |      |      |      |Aud on|Audoff|AGnorm|AGswap|Qwerty|Colemk|Dvorak|Plover|      |
+   * |------+------+------+------+------+------|------+------+------+------+------+------|
+   * |      |Voice-|Voice+|Mus on|Musoff|MIDIon|MIDIof|      |      |      |      |      |
+   * |------+------+------+------+------+------+------+------+------+------+------+------|
+   * |      |      |      |      |      |             |      |      |      |      |      |
+   * `-----------------------------------------------------------------------------------'
+   */
+  [_ADJUST] = LAYOUT_ortho_4x12(
+    _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+    _______, _______, _______, _______, _______, _______, _______, QWERTY,  DVORAK,  _______, _______, _______,
+    _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+    _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET
+  ),
+
+  [_FUNC] = LAYOUT_ortho_4x12(
+    _______, _______, _______, _______, _______, _______, _______, _______, KC_UP,   _______, KC_PSCR, _______,
+    _______, _______, _______, _______, _______, _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______,
+    _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+    _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______
+  ),
+
+  [_NUMB] = LAYOUT_ortho_4x12(
+    _______, _______, _______, _______, _______, _______, _______, KC_7,    KC_8,    KC_9,    _______, KC_BSPC,
+    _______, _______, _______, _______, _______, _______, _______, KC_4,    KC_5,    KC_6,    _______, _______,
+    _______, _______, _______, _______, _______, _______, _______, KC_1,    KC_2,    KC_3,    _______, _______,
+    _______, _______, _______, _______, _______, _______, _______, KC_0,    KC_0,    _______, _______, _______
+  )
+
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QWERTY:
+      if (record->event.pressed) {
+        // print("mode just switched to qwerty and this is a huge string\n");
+        set_single_persistent_default_layer(_QWERTY);
+      }
+      return false;
+      break;
+    case DVORAK:
+      if (record->event.pressed) {
+        set_single_persistent_default_layer(_DVORAK);
+      }
+      return false;
+      break;
+    case LOWER:
+      if (record->event.pressed) {
+        layer_on(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+      break;
+    case RAISE:
+      if (record->event.pressed) {
+        layer_on(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+      break;
+    case ADJUST:
+      if (record->event.pressed) {
+        layer_on(_ADJUST);
+      } else {
+        layer_off(_ADJUST);
+      }
+      return false;
+      break;
+  }
+  return true;
+}

keyboards/contra/keymaps/msiu/readme.md

@@ -0,0 +1,2 @@
+# The Default Contra Layout
+

keyboards/converter/usb_usb/keymaps/default/config.h

@@ -1,6 +1,3 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
 
-#include "../../config.h"
-
-#endif
+// place overrides here

keyboards/cospad/keymaps/default/keymap.c

@@ -1,10 +1,6 @@
 #include QMK_KEYBOARD_H
 #include "led.h"
 
-#ifdef RGBLIGHT_ENABLE
-#include "rgblight.h"
-#endif
-
 // Each layer gets a name for readability, which is then used in the keymap matrix below.
 // The underscores don't mean anything - you can have a layer called STUFF or any other name.
 // Layer names don't all need to be of the same length, obviously, and you can also skip them

keyboards/cu24/keymaps/default/keymap.c

@@ -13,7 +13,7 @@
  * You should have received a copy of the GNU General Public License
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
-#include "cu24.h"
+#include QMK_KEYBOARD_H
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 [0] = LAYOUT_grid( /* Base */

keyboards/cu75/keymaps/default/config.h

@@ -1,8 +1,3 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
-
-#include "../../config.h"
+#pragma once
 
 // place overrides here
-
-#endif

keyboards/deltasplit75/keymaps/default/config.h

@@ -16,16 +16,10 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
 
+#pragma once
+
 #define USE_SERIAL
 
 #define MASTER_LEFT
 // #define MASTER_RIGHT
 // #define EE_HANDS
-
-
-#ifdef SUBPROJECT_v2
-    #include "../../v2/config.h"
-#endif
-#ifdef SUBPROJECT_protosplit
-    #include "../../protosplit/config.h"
-#endif

keyboards/dichotomy/keymaps/default/keymap.c

@@ -1,7 +1,7 @@
 // this is the style you want to emulate.
 // This is the canonical layout file for the Quantum project. If you want to add another keyboard,
 
-#include "dichotomy.h"
+#include QMK_KEYBOARD_H
 
 // Each layer gets a name for readability, which is then used in the keymap matrix below.
 // The underscores don't mean anything - you can have a layer called STUFF or any other name.

keyboards/diverge3/keymaps/default/config.h

@@ -14,14 +14,9 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
-
-#include "config_common.h"
+#pragma once
 
 // place overrides here
 #define MASTER_RIGHT
 #define PERMISSIVE_HOLD
 #define TAPPING_TERM 150
-
-#endif

keyboards/dk60/dk60.c

@@ -1,5 +1,15 @@
 #include "dk60.h"
 
+extern inline void dk60_caps_led_on(void);
+extern inline void dk60_esc_led_on(void);
+
+extern inline void dk60_caps_led_off(void);
+extern inline void dk60_esc_led_off(void);
+
+extern inline void dk60_led_all_on(void);
+extern inline void dk60_led_all_off(void);
+
+
 void dk60_blink_all_leds(void)
 {
     dk60_led_all_off();

keyboards/do60/keymaps/default/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-#include "action_layer.h"
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 

keyboards/dozen0/config.h

@@ -112,11 +112,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
 
-/* key combination for magic key command */
-/*#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)*/
-
 /* control how magic key switches layers */
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true

keyboards/dztech/dz40rgb/config.h

@@ -22,7 +22,6 @@
 #define DEBOUNCE 3
 #define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
 #define RGB_DISABLE_WHEN_USB_SUSPENDED false // turn off effects when suspended
-#define RGB_MATRIX_SKIP_FRAMES 10
 #define RGB_MATRIX_KEYPRESSES
 #define DISABLE_RGB_MATRIX_SPLASH
 #define DISABLE_RGB_MATRIX_MULTISPLASH

keyboards/dztech/dz60rgb/config.h

@@ -23,7 +23,6 @@
 #define DEBOUNCE 3
 #define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
 #define RGB_DISABLE_WHEN_USB_SUSPENDED false // turn off effects when suspended
-#define RGB_MATRIX_SKIP_FRAMES 10
 #define RGB_MATRIX_KEYPRESSES
 #define DISABLE_RGB_MATRIX_SPLASH
 #define DISABLE_RGB_MATRIX_MULTISPLASH

keyboards/ergodash/rev1/keymaps/default/config.h

@@ -18,10 +18,9 @@ You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
 
-#include "../../config.h"
+// place overrides here
 
 /* Use I2C or Serial, not both */
 
@@ -34,8 +33,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 // #define MASTER_RIGHT
 // #define EE_HANDS
 
-#endif
-
 #undef RGBLED_NUM
 #define RGBLIGHT_ANIMATIONS
 #define RGBLED_NUM 24

keyboards/ergodash/rev1/keymaps/default/keymap.c

@@ -1,6 +1,4 @@
 #include QMK_KEYBOARD_H
-#include "action_layer.h"
-#include "eeconfig.h"
 
 extern keymap_config_t keymap_config;
 

keyboards/ergodash/rev2/keymaps/default/config.h

@@ -18,10 +18,9 @@ You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
 
-#include "../../config.h"
+// place overrides here
 
 /* Use I2C or Serial, not both */
 
@@ -34,7 +33,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 // #define MASTER_RIGHT
 // #define EE_HANDS
 
-#endif
 
 #undef RGBLED_NUM
 #define RGBLIGHT_ANIMATIONS

keyboards/ergodash/rev2/keymaps/default/keymap.c

@@ -1,6 +1,4 @@
 #include QMK_KEYBOARD_H
-#include "action_layer.h"
-#include "eeconfig.h"
 
 extern keymap_config_t keymap_config;
 

keyboards/ergodone/keymaps/default/keymap.c

@@ -1,6 +1,4 @@
 #include QMK_KEYBOARD_H
-#include "debug.h"
-#include "action_layer.h"
 #include "version.h"
 
 #define BASE 0 // default layer

keyboards/ergodox_ez/config.h

@@ -109,7 +109,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DRIVER_1_LED_TOTAL 24
 #define DRIVER_2_LED_TOTAL 24
 #define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL
-#define RGB_MATRIX_SKIP_FRAMES 10
 
 // #define RGBLIGHT_COLOR_LAYER_0 0x00, 0x00, 0xFF
 /* #define RGBLIGHT_COLOR_LAYER_1 0x00, 0x00, 0xFF */

keyboards/ergodox_ez/ergodox_ez.c

@@ -269,69 +269,68 @@ const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
 };
 
 
-__attribute__ ((weak))
 const rgb_led g_rgb_leds[DRIVER_LED_TOTAL] = {
 
     /*{row | col << 4}
       |             {x=0..224, y=0..64}
       |              |                    modifier
       |              |                    | */
-    {{0|(0<<4)},   {24.9*5, 16*0}, 0}, // LED 1 on right
-    {{0|(1<<4)},   {24.9*6, 16*0}, 0}, // LED 2
-    {{0|(2<<4)},   {24.9*7, 16*0}, 0}, // LED 3
-    {{0|(3<<4)},   {24.9*8, 16*0}, 0}, // LED 4
-    {{0|(4<<4)},   {24.9*9, 16*0}, 0}, // LED 5
+    {{ 8|(0<<4)},   {17.2* 8, 12.8*0}, 0}, // LED 1 on right > Key 6
+    {{ 9|(0<<4)},   {17.2* 9, 12.8*0}, 0}, // LED 2 > Key 7
+    {{10|(0<<4)},   {17.2*10, 12.8*0}, 0}, // LED 3 > Key 8
+    {{11|(0<<4)},   {17.2*11, 12.8*0}, 0}, // LED 4 > Key 9
+    {{12|(0<<4)},   {17.2*12, 12.8*0}, 0}, // LED 5 > Key 0
 
-    {{1|(5<<4)},   {24.9*5, 16*1}, 0}, // LED 6
-    {{1|(6<<4)},   {24.9*6, 16*1}, 0}, // LED 7
-    {{1|(7<<4)},   {24.9*7, 16*1}, 0}, // LED 8
-    {{1|(8<<4)},   {24.9*8, 16*1}, 0}, // LED 9
-    {{1|(9<<4)},   {24.9*9, 16*1}, 0}, // LED 10
+    {{ 8|(1<<4)},   {17.2* 8, 12.8*1}, 0}, // LED 6
+    {{ 9|(1<<4)},   {17.2* 9, 12.8*1}, 0}, // LED 7
+    {{10|(1<<4)},   {17.2*10, 12.8*1}, 0}, // LED 8
+    {{11|(1<<4)},   {17.2*11, 12.8*1}, 0}, // LED 9
+    {{12|(1<<4)},   {17.2*12, 12.8*1}, 0}, // LED 10
 
-    {{2|(5<<4)},   {24.9*5, 16*2}, 0}, // LED 11
-    {{2|(6<<4)},   {24.9*6, 16*2}, 0}, // LED 12
-    {{2|(7<<4)},   {24.9*7, 16*2}, 0}, // LED 13
-    {{2|(8<<4)},   {24.9*8, 16*2}, 0}, // LED 14
-    {{2|(9<<4)},   {24.9*9, 16*2}, 0}, // LED 15
+    {{ 8|(2<<4)},   {17.2* 8, 12.8*2}, 0}, // LED 11
+    {{ 9|(2<<4)},   {17.2* 9, 12.8*2}, 0}, // LED 12
+    {{10|(2<<4)},   {17.2*10, 12.8*2}, 0}, // LED 13
+    {{11|(2<<4)},   {17.2*11, 12.8*2}, 0}, // LED 14
+    {{12|(2<<4)},   {17.2*12, 12.8*2}, 0}, // LED 15
 
-    {{3|(5<<4)},   {24.9*5, 16*2}, 0}, // LED 16
-    {{3|(6<<4)},   {24.9*6, 16*2}, 0}, // LED 17
-    {{3|(7<<4)},   {24.9*7, 16*2}, 0}, // LED 18
-    {{3|(8<<4)},   {24.9*8, 16*2}, 0}, // LED 19
-    {{3|(9<<4)},   {24.9*9, 16*2}, 0}, // LED 20
+    {{ 8|(3<<4)},   {17.2* 8, 12.8*3}, 0}, // LED 16
+    {{ 9|(3<<4)},   {17.2* 9, 12.8*3}, 0}, // LED 17
+    {{10|(3<<4)},   {17.2*10, 12.8*3}, 0}, // LED 18
+    {{11|(3<<4)},   {17.2*11, 12.8*3}, 0}, // LED 19
+    {{12|(3<<4)},   {17.2*12, 12.8*3}, 0}, // LED 20
 
-    {{4|(6<<4)},   {24.9*6, 16*2}, 0}, // LED 21
-    {{4|(7<<4)},   {24.9*7, 16*2}, 0}, // LED 22
-    {{4|(8<<4)},   {24.9*8, 16*2}, 0}, // LED 23
-    {{4|(9<<4)},   {24.9*9, 16*2}, 0}, // LED 24
+    {{ 9|(4<<4)},   {17.2* 9, 12.8*4}, 1}, // LED 21
+    {{10|(4<<4)},   {17.2*10, 12.8*4}, 1}, // LED 22
+    {{11|(4<<4)},   {17.2*11, 12.8*4}, 1}, // LED 23
+    {{12|(4<<4)},   {17.2*12, 12.8*4}, 1}, // LED 24
 
-    {{0|(0<<4)},   {24.9*4, 16*0}, 0}, // LED 1 on left
-    {{0|(1<<4)},   {24.9*3, 16*0}, 0}, // LED 2
-    {{0|(2<<4)},   {24.9*2, 16*0}, 0}, // LED 3
-    {{0|(3<<4)},   {24.9*1, 16*0}, 0}, // LED 4
-    {{0|(4<<4)},   {24.9*0, 16*0}, 0}, // LED 5
+    {{ 5|(0<<4)},   {17.2* 5, 12.8*0}, 0}, // LED 1 on left > Key 5
+    {{ 4|(0<<4)},   {17.2* 4, 12.8*0}, 0}, // LED 2 > Key 4
+    {{ 3|(0<<4)},   {17.2* 3, 12.8*0}, 0}, // LED 3 > Key 3
+    {{ 2|(0<<4)},   {17.2* 2, 12.8*0}, 0}, // LED 4 > Key 2
+    {{ 1|(0<<4)},   {17.2* 1, 12.8*0}, 0}, // LED 5 > Key 1
 
-    {{1|(5<<4)},   {24.9*4, 16*1}, 0}, // LED 6
-    {{1|(6<<4)},   {24.9*3, 16*1}, 0}, // LED 7
-    {{1|(7<<4)},   {24.9*2, 16*1}, 0}, // LED 8
-    {{1|(8<<4)},   {24.9*1, 16*1}, 0}, // LED 9
-    {{1|(9<<4)},   {24.9*0, 16*1}, 0}, // LED 10
+    {{ 5|(1<<4)},   {17.2* 5, 12.8*1}, 0}, // LED 6
+    {{ 4|(1<<4)},   {17.2* 4, 12.8*1}, 0}, // LED 7
+    {{ 3|(1<<4)},   {17.2* 3, 12.8*1}, 0}, // LED 8
+    {{ 2|(1<<4)},   {17.2* 2, 12.8*1}, 0}, // LED 9
+    {{ 1|(1<<4)},   {17.2* 1, 12.8*1}, 0}, // LED 10
 
-    {{2|(5<<4)},   {24.9*4, 16*2}, 0}, // LED 11
-    {{2|(6<<4)},   {24.9*3, 16*2}, 0}, // LED 12
-    {{2|(7<<4)},   {24.9*2, 16*2}, 0}, // LED 13
-    {{2|(8<<4)},   {24.9*1, 16*2}, 0}, // LED 14
-    {{2|(9<<4)},   {24.9*0, 16*2}, 0}, // LED 15
+    {{ 5|(2<<4)},   {17.2* 5, 12.8*2}, 0}, // LED 11
+    {{ 4|(2<<4)},   {17.2* 4, 12.8*2}, 0}, // LED 12
+    {{ 3|(2<<4)},   {17.2* 3, 12.8*2}, 0}, // LED 13
+    {{ 2|(2<<4)},   {17.2* 2, 12.8*2}, 0}, // LED 14
+    {{ 1|(2<<4)},   {17.2* 1, 12.8*2}, 0}, // LED 15
 
-    {{3|(5<<4)},   {24.9*4, 16*2}, 0}, // LED 16
-    {{3|(6<<4)},   {24.9*3, 16*2}, 0}, // LED 17
-    {{3|(7<<4)},   {24.9*2, 16*2}, 0}, // LED 18
-    {{3|(8<<4)},   {24.9*1, 16*2}, 0}, // LED 19
-    {{3|(9<<4)},   {24.9*0, 16*2}, 0}, // LED 20
+    {{ 5|(3<<4)},   {17.2* 5, 12.8*3}, 0}, // LED 16
+    {{ 4|(3<<4)},   {17.2* 4, 12.8*3}, 0}, // LED 17
+    {{ 3|(3<<4)},   {17.2* 3, 12.8*3}, 0}, // LED 18
+    {{ 2|(3<<4)},   {17.2* 2, 12.8*3}, 0}, // LED 19
+    {{ 1|(3<<4)},   {17.2* 1, 12.8*3}, 0}, // LED 20
 
-    {{4|(6<<4)},   {24.9*3, 16*2}, 0}, // LED 21
-    {{4|(7<<4)},   {24.9*2, 16*2}, 0}, // LED 22
-    {{4|(8<<4)},   {24.9*1, 16*2}, 0}, // LED 23
-    {{4|(9<<4)},   {24.9*0, 16*2}, 0}, // LED 24
+    {{ 4|(4<<4)},   {17.2* 4, 12.8*4}, 1}, // LED 21
+    {{ 3|(4<<4)},   {17.2* 3, 12.8*4}, 1}, // LED 22
+    {{ 2|(4<<4)},   {17.2* 2, 12.8*4}, 1}, // LED 23
+    {{ 1|(4<<4)},   {17.2* 1, 12.8*4}, 1}, // LED 24 > Key Hack
 };
 #endif

keyboards/ergodox_infinity/keymaps/default/keymap.c

@@ -1,6 +1,4 @@
 #include QMK_KEYBOARD_H
-#include "debug.h"
-#include "action_layer.h"
 #include "version.h"
 
 #define BASE 0 // default layer